View SC26C198_766627.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
Table of Contents Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Uses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
Register Map Detail . . . . . . . . . . . . . . . . . . . . . . . . 364 Reset Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
Device Configuration after Hardware Reset or CRa cmd=x1F Cleared registers: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clears Modes for: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disables: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Halts: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Limitations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 372 372 372 372 373
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337 Pin Configurations . . . . . . . . . . . . . . . . . . . . . . . . . 338 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . Conceptual Overview . . . . . . . . . . . . . . . . . . . . . . .
Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Asynchronous bus cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . Synchronous bus cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timing Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sclk - System Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baud Rate Generator BRG . . . . . . . . . . . . . . . . . . . . . . . . BRG Counters (Used for random baud rate generation) Channel Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Character Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Global Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
339 340 340 340
340 340 340 341 341 341 341 341 341 341 342 342 342
DC Electrical Specifications (26C198 and 68C198) . . . . . . . . . . . . . . . . . . . . . . . DC Electrical Specifications (26L198 and 68L198) . . . . . . . . . . . . . . . . . . . . . . . AC Electrical Characteristics5 (26L198 and 68L198) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
373 376 377 383
DESCRIPTION
The Philips 26C198 Octal UART is a single chip CMOS-LSI communications device that provides 8 full-duplex asynchronous channels with significantly deeper 16 byte FIFOs, Automatic in-band flow control using Xon/Xoff characters defined by the user and address recognition in the wake up mode. Synchronous bus interface is used for all communication between host and OCTART. It is fabricated using Philips 1.0 micron CMOS technology that combines the benefits of low cost, high density and low power consumption. The operating speed of each receiver and transmitter can be selected independently from one of 22 fixed baud rates, a 16X clock derived from one of two programmable baud rate counters or one of three external 16X clocks (1 available at 1x clock rate). The baud rate generator and counter can operate directly from a crystal or from seven other external or internal clock inputs. The ability to independently program the operating speed of the receiver and transmitter makes the Octal UART particularly attractive for dual speed full duplex channel applications such as clustered terminal systems. The receivers and transmitters are buffered with FIFOs of 16 characters to minimize the potential for receiver overrun and to reduce interrupt overhead. In addition, a handshaking capability and in-band flow control are provided to disable a remote UART transmitter when the receiver buffer is full or nearly so. To minimize interrupt overhead an interrupt arbitration system is included which reports the context of the interrupting UART via direct access or through the modification of the interrupt vector. The context of the interrupt is reported as channel number, type of device interrupting ( receiver COS etc.) and, for transmitters or receivers, the fill level of the FIFO. The Octal UART provides a power down mode in which the oscillator is stopped but the register contents are maintained. This results in reduced power consumption of several orders of magnitudes. The Octal UART is fully TTL compatible when operating from a single +5V power supply. Operation at 3.3 volts is maintained with CMOS interface levels. The device also offered in a version which maintains TTL input and output levels while operating with a 3.3 volt power supply.
Detailed Descriptions . . . . . . . . . . . . . . . . . . . . . . . 342 Receiver and Transmitter . . . . . . . . . . . . . . . . . . . 342
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmitter Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmission of "break" . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1x and 16x modes, Transmitter . . . . . . . . . . . . . . . . . . . . . Transmitter FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1x and 16x mode, Receiver . . . . . . . . . . . . . . . . . . . . . . . . . Receiver Status Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Receiver FIFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RxFIFO Status: Status reporting modes . . . . . . . . . . . . . . I/O ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Purpose Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Global Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Character Recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Xon Xoff Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multi-drop or Wake up or 9 bit mode . . . . . . . . . . . . . . . . . Character Stripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interrupt Arbitration and IRQN generation . . . . . . . . . . . . . . . . IACKN Cycle, Update CIR . . . . . . . . . . . . . . . . . . . . . . . . . . Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabling and Activating Interrupt sources . . . . . . . . . . . . . Setting Interrupt Priorities . . . . . . . . . . . . . . . . . . . . . . . . . . Major Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Minor Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Watch-dog Timer Time-out Mode . . . . . . . . . . . . . . . . . . . Wake Up Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Xon/Xoff Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342 342 343 343 343 343 343 343 344 344 344 345 345 345 345 345 345 345 346 346 346 346 347 348 348 348 349
Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . 347
REGISTER DEfiniTIONS . . . . . . . . . . . . . . . . . . . . 351
MR - Mode Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351 UCIR - Update CIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
General Purpose Output Pin Control . . . . . . . . 361 Register Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 Register Map Summary . . . . . . . . . . . . . . . . . . . . . 363
1995 May 1
336
853-1756 15179
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
Uses
Statistical Multiplexers Data Concentrators Packet-switching networks Process Control Building or Plant Control Laboratory data gathering ISDN front ends Computer Networks Point-of-Sale terminals Automotive, cab and engine controls Entertainment systems MIDDI keyboard control music systems Theater lighting control Terminal Servers Computer-Printer/Plotter links
* IACKN and DACKN signal pins * Watch dog timer for each receiver (64 receive clock counts) * Programmable Data Formats:
- 5 to 8 data bits plus parity - Odd, even force or no parity - 1, 1.5 or 2 stop bits
* Flexible baud rate selection for receivers and transmitters:
- 22 fixed rates; 50 - 230.4K baud or 100 to 460.8K baud - Additional non-standard rates to 500K baud with internal generators - Two reload-counters provide additional programmable baud rate generation - External 1x or 16x clock inputs - Simplified baud rate selection
FEATURES
* Single 3.3v power supply * Eight Philips industry standard full duplex UART channels * Sixteen byte receiver FIFOs for each UART * Sixteen byte transmit FIFOs for each UART * In band flow control using programmable Xon/Xoff characters * Flow control using CTSN RTSN hardware handshaking * Automatic address detection in multi-drop mode * Three byte general purpose character recognition * Fast data bus, 30 ns data bus release time, 125 ns bus cycle time * Programmable interrupt priorities * Automatic identification of highest priority interrupt pending * Global interrupt and control registers ease setup and interrupt
handling
* 1 MHz 1x and 16x data rates full duplex all channels. * Parity, framing and overrun error detection * False start bit detection * Line break detection and generation * Programmable channel mode
- Normal(full duplex) - Diagnostic modes automatic echo local loop back emote loop back
* Four I/O ports per UART for modem controls, clocks, RTSN, I/O
etc. - All I/O ports equipped with "Change of State Detectors"
* Vectored interrupts with programmable interrupt vector formats
- Interrupt vector modified with channel number - Interrupt vector modified with channel number and channel type - Interrupt vector not modified
* Two global inputs and two global outputs for general purpose I/O * Power down mode * On chip crystal oscillator, 2-8 MHz * TTL input levels. Outputs switch between full VCC and VSS * High speed CMOS technology * 68 pin PLCC
VCC = 5V 10%
ORDERING CODE
PACKAGES 84-Pin Plastic Leaded Chip Carrier (PLCC) 84-Pin Plastic Leaded Chip Carrier (PLCC) Commercial 0C to +70C SC26C198C1A SC68C198C1A Commercial 0C to +70C 84-Pin Plastic Leaded Chip Carrier (PLCC) 84-Pin Plastic Leaded Chip Carrier (PLCC) NOTES: 1. For availability, please contact factory. 1995 May 1 337 SC26L198C1A SC68L198C1A Industrial1 -40C to +85C SC26C198A1A SC68C198A1A Industrial1 -40C to +85C SC26L198A1A SC68L198A1A SOT189-3 SOT189-3 DWG # SOT189-3 SOT189-3
VCC = 3.3V 10%
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAA AAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A
PINOUT
Pin 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 10 11 9 8 7 6 5 4 3 2 1 Function DACKN W_RN RxDb RxDa RxDc I/O0d I/O3b I/O2b I/O1b I/O0b I/O3a I/O2a I/O1a I/O0a I/O3c I/O2c I/O1c I/O0c TxDb TxDa TxDc CEN VCC VSS Vss A0 A1 A2 Pin 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
32 33 84-Pin PLCC TOP VIEW
1995 May 1
PIN CONFIGURATIONS
Philips Semiconductors
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
12
11
338
1
Function
RESETN
53
75
Gout0
RxDh RxDd I/O0h I/O1h I/O2h I/O3h I/O3d I/O2d I/O1d TxDd Gin1 Gin0 VCC VSS Vss Vss D7 D6 D5 D4 D3 D2 D1 D0
54 74
I/O3g TxDh
SC26C198 SC68C198 SC26L198 SC68L198
Pin
84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57
Product specification
Function
IACKN IRQN RxDe RxDg I/O0e I/O1e I/O2e I/O3e I/O0g I/O1g I/O2g TxDe TxDg RxDf I/O0f I/O1f I/O2f I/O3f TxDf VSS A3 A4 A5 A6 A7 X2 X1
SCLK
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA
NOTES: 1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and the functional operation of the device at these or any other conditions above those indicated in the Operation Section of this specification is not implied.
1995 May 1
ABSOLUTE MAXIMUM RATINGS
NOTE: Many output pins will have very fast edges, especially when lightly loaded (less than 20 pf.) These edges may move as fast as 1 to 3 ns fall or rise time. The user must be aware of the possible generation of ringing and reflections on improperly terminated interconnections. See previous note on Sclk noise under pin assignments.
Philips Semiconductors
Pin Description
Power Supplies
X2
X1/CCLK
RESETN
GOUT0
GIN(1:0)
I/O3(a-d)
I/O2(a-d)
I/O1(a-d)
I/O0(a-d)
RD(a-h)
TD(a-h)
IACKN
IRQN
DACKN
W_RN
D(7:0)
A(7:0)
CEN
SClk
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
MNEMONIC
SYMBOL
TSTG
PD3
PD5
VCC
VSS
TA
TYPE
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
I
I
I
I
I
I
I
I
I
I
Write Read not control: When high indicates that the host CPU will write to a 26C198 register or transmit FIFO. When low, indicates a read cycle. 0 = Read; 1 = Write
Chip select: Active low. When asserted, allows I/O access to OCTART registers by host CPU. W_RN signal indicates direction. (Must not be active in IACKN cycle)
16 pins total 8 pins for Vss, 8 pins for Vcc
Crystal 2: If a crystal is used, this is the connection to the second terminal. If a clock signal drives X1, this pin must be left unconnected.
Crystal 1 or Communication Clock: This pin may be connected to one side of a 2-8 MHz crystal. It may alternatively be driven by an external clock in this frequency range. Standard frequency = 3.6864 MHz
Master reset: Active Low. Must be asserted at power up and may be asserted at other times to reset and restart the system. See "Reset Conditions" at end of register map. Minimum width 10 SCLK.
Global general purpose outputs, available from any channel.
Global general purpose inputs, available to any/all channels.
Input/Output 3: Multi-use input or output pin for the UART.
Input/Output 2: Multi-use input or output pin for the UART.
Input/Output 1: Multi-use input or output pin for the UART.
Input/Output 0: Multi-use input or output pin for the UART.
Receive Data: Serial inputs to the 8 UARTs
Transmit Data: Serial outputs from the 8 UARTs.
Interrupt Acknowledge: Active low. When asserted, indicates that the host CPU has initiated an interrupt acknowledge cycle. (Do not use CEN in an IACKN cycle)
Interrupt Request: Active low. When asserted, indicates that the 26C198 requires service for pending interrupt(s). Open drain.
Data Acknowledge: Active low. When asserted, it signals that the last transfer of the D lines is complete. Open drain.
8-bit bi-directional data bus. Carries command and status information between 26C198 and the host CPU. Used to convey parallel data for serial I/O between the host CPU and the 26C198
Address lines (A[6] is NOT used. See "Host Interface" )
Host system clock. Used to time operations in the Host Interface and clock internal logic. Must be greater than twice the frequency of highest X1, Counter/Timer, TxC (1x) or RxC (1x) input frequency.
Operating ambient temperature range
Power Dissipation at VCC = 3.3 Volts
Power Dissipation at VCC = 5.0 Volts
Voltage from any pin to GND
Storage temperature range
Voltage from VDD to GND
PARAMETER
339 DESCRIPTION -0.5 to VCC + 0.5 -0.5 to +7.0 -65 to +150 See Note 3 RATING
SC26C198 SC68C198 SC26L198 SC68L198
0.5 1.2
Product specification
UNIT
C
C
W W V V
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
BLOCK DIAGRAM
FULL DUPLEX UART CHANNEL
FULL DUPLEX UART CHANNEL DATA DRIVERS AND MODEM INTERFACE
FULL DUPLEX UART CHANNEL INTERRUPT ARBITRATION TIMING AND BAUD RATE GENERATOR I/O PORT TIMING AND INTERFACE HOST INTERFACE
FULL DUPLEX UART CHANNEL
FULL DUPLEX UART CHANNEL
FULL DUPLEX UART CHANNEL
FULL DUPLEX UART CHANNEL
FULL DUPLEX UART CHANNEL
INPUT BUFFERS AND OUTPUT DRIVERS
Block Diagram SC26/68C198 As shown in the block diagram, the Octal UART consists of: an interrupt arbiter, host interface, timing blocks and eight UART channel blocks. The eight channels blocks operate independently, interacting only with the timing, host I/F and interrupt blocks.
SD00193
cycles after CEN is recognized. These four cycles are the C1, C2, C3, C4 periods shown in the timing diagrams. DACKN always occurs in the C4 time and occurs approximately 18 ns after the rising edge of C4. Addressing of the various functions of the OCTART is through the address bus A(7:0). The 26C198 is compatible with the SC28L194 Quad UART in software and function. A[7], in a general sense, is used to separate the data portion of the circuit from the control portion. Asynchronous bus cycle The asynchronous mode requires one bus cycle of the chip select (CEN) for each read or write to the chip. No more action will occur on the bus after the C4 time until CEN is returned high. Synchronous bus cycle In the synchronous mode a read or write will be done every four cycles of the Sclk. CEN does not require cycling but must remain low to keep the synchronous accesses active. This provides a burst mode of access to the chip. In both cases each read or write operation(s) will be completed in four (4) Sclk cycles. The difference in the two modes is only that the asynchronous mode will not begin another bus cycle if the CEN remains active after the four internal Sclk have completed. Internally the asynchronous cycle will terminate after the four periods of Sclk regardless of how long CEN is held active In all cases the internal action will terminate at the withdrawal of CEN. Synchronous CEN cycles shorter than multiples of four Sclk cycles minus 1 Sclk and asynchronous CEN cycles shorter than four Sclk cycles may cause short read or write cycles and produce corrupted data transfers. 340
FUNCTIONAL DESCRIPTION
The SC26C198 is composed of several functional blocks:
* Synchronous host interface block * A timing block consisting of a common baud rate generator
making 22 industry standard baud rates and 2 16-bit counters used for non-standard baud rate generation
* 4 identical independent full duplex UART channel blocks * Interrupt arbitration system evaluating 24 contenders * I/O port control section and change of state detectors.
CONCEPTUAL OVERVIEW Host Interface
The Host interface is comprised of the signal pins CEN, W/RN, IACKN, DACKN, IRQN Sclk and provides all the control for data transfer between the external and internal data buses of the host and the OCTART. The host interface operates in a synchronous mode with the system (Sclk) which has been designed for a nominal operating frequency of 33 MHz. The interface operates in either of two modes; synchronous or asynchronous to the Sclk However the bus cycle within the OCTART always takes place in four Sclk 1995 May 1
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
Timing Circuits
The timing block consists of a crystal oscillator, a fixed baud rate generator (BRG), a pair of programmable 16 bit register based counters. A buffer for the System Clock generates internal timing for processes not directly concerned with serial data flow. Crystal Oscillator The crystal oscillator operates directly from a crystal, tuned between 1.0 and 8.0 MHz, connected across the X1/CCLK and X2 inputs with a minimum of external components. BRG values listed for the clock select registers correspond to a 3.6864 MHz crystal frequency. Use of a 7.3728 MHz crystal will double the Communication Clock frequencies. An external clock in the 100 KHz to 10 MHz frequency range may be connected to X1/CCLK. If an external clock is used instead of a crystal, X1/CCLK must be driven and X2 left floating. The X1 clock serves as the basic timing reference for the baud rate generator (BRG) and is available to the BRG timers . The X1 oscillator input may be left unused if the internal BRG is not used and the X1 signal is not selected for any counter input. Sclk - System Clock A clock frequency, within the limits specified in the electrical specifications, must be supplied for the system clock Sclk. To ensure the proper operation of internal controllers, the Sclk frequency provided, must be strictly greater than twice the frequency of X1 crystal clock, or any external 1x data clock input. The system clock serves as the basic timing reference for the host interface and other internal circuits. Baud Rate Generator BRG The baud rate generator operates from the oscillator or external X1/CCLK clock input and is capable of generating 22 commonly used data communications baud rates ranging from 50 to 230.4K baud. These common rates may be doubled (up to 460.8 and 500K baud) when faster clocks are used on the X1/X2 clock inputs. (See Receiver and Transmitter Clock Select Register descriptions.) All of these are available simultaneously for use by any receiver or transmitter. The clock outputs from the BRG are at 16X the actual baud rate. BRG Counters (Used for random baud rate generation) The two BRG Timers are programmable 16 bit dividers that are used for generating miscellaneous clocks. These clocks may be used by any or all of the receivers and transmitters in the Octart or output on the general purpose output pin GPO. Each timer unit has eight different clock sources available to it as described in the BRG Timer Control Register. (BRGTCR). Note that the timer run and stop controls are also contained in this register. The BRG Timers generate a symmetrical square wave whose half period is equal in time to the division of the selected BRG Timer clock source by the number loaded to the BRG Timer Reload Registers ( BRGTRU and BRGTRL). Thus, the output frequency will be the clock source frequency divided by twice the value loaded to the BRGTRU and BRGTRL registers. This is the result of counting down once for the high portion of the output wave and once for the low portion. Whenever the these timers are selected via the receiver or transmitter Clock Select register their output will be configured as a 16x clock for the respective receiver or transmitter. Therefore one needs to program the timers to generate a clock 16 times faster than the data rate. The formula for calculating 'n', the number loaded to the BRGTRU and BRGTRL registers, is shown below. 1995 May 1 341
n+
BRG Timer Input frequency 2 @ 16 @ desired baud rate
-1
Note: 'n' may assume values of 0 and 1. In previous Philips data communications controllers these values were not allowed. The BRG timer input frequency is controlled by the BRG Timer control register (BRGTCR) The frequency generated from the above formula will be at a rate 16 times faster than the desired baud rate. The transmitter and receiver state machines include divide by 16 circuits which provide the final frequency and provide various timing edges used in the qualifying the serial data bit stream. Often this division will result in a non-integer value; 26.3 for example. One may only program integer numbers to a digital divider. There for 26 would be chosen. If 26.7 was the result of the division then 27 would be chosen. This gives a baud rate error of 0.3/26.3 or 0.3/26.7. which yields a percentage error of 1.14% or 1.12% respectively; well within the ability of the asynchronous mode of operation. One should be cautious about the assumed benign effects of small errors since the other receiver or transmitter with which one is communicating may also have a small error in the precise baud rate. In a "clean" communications environment using one start bit, eight data bits and one stop bit the total difference allowed between the transmitter and receiver frequency is approximately 4.6%. Less than eight data bits will increase this percentage.
Channel Blocks
There are eight channel blocks, each containing an I/O port control, a data format control, and a single full duplex UART channel consisting of a receiver and a transmitter with their associated 16 byte FIFOs. Each block has its own status register, interrupt status and interrupt mask registers and their interface to the interrupt arbitration system. A highly programmable character recognition system is also included in each block. This system is used for the Xon/Xoff flow control and the multi-drop ("9 bit mode") address character recognition. It may also be used for general purpose character recognition. Four I/O pins are provided for each channel. These pins are configured individually to be inputs or outputs. As inputs they may be used to bring external data to the bus, as clocks for internal functions or external control signals. Each I/O pin has a "Change of State" detector. The change detectors are used to signal a change in the signal level at the pin (Either 0 to 1 or 1 to 0). The level change on these pins must be stable for 25 to 50 Us (two edges of the 38.4 KHz baud rate clock) before the detectors will signal a valid change. These are typically used for interface signals from modems to the OCTART and from there to the host. See the description of the "UART channel" under detailed descriptions below. Character Recognition Character recognition is specific to each of the eight UARTs. Three programmable characters are provided for the character recognition for each channel. The three are general purpose in nature and may be set to only cause an interrupt or to initiate some rather complex operations specific to "Multi-drop" address recognition or in-band Xon/Xoff flow control. Character recognition is accomplished via CAM memory. The Content Addressable Memory continually examines the incoming data stream. Upon the recognition of a control character appropriate bits are set in the Xon/Xoff Interrupt Status Register (XISR) and Interrupt Status Register (ISR). The setting of these bit(s) will
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
initiate any of the automatic sequences or and/or an interrupt that may have enabled via the MR0 register. The characters of the recognition system are not controlled by the software or hardware reset. They do not have a pre-defined "reset value". They may, however, be loaded by a "Gang White" or "Gang Load" command as described in the "Xon Xoff Characters" paragraph. Note: Character recognition is further described in the Minor Modes of Operation.
content of the CIR (Current Interrupt Register) as a result of an interrupt arbitration. In other words they are indirect registers contained in the Current Interrupt Register (CIR) which the CIR uses to point to the source and context of the OCTART sub circuit presently causing an interrupt. The principle purpose of these "registers" is improving the efficiency of the interrupt service. The global registers and the CIR update procedure are further described in the Interrupt Arbitration system I/O Ports Each of the eight UART blocks contains an I/O section of four ports. These ports function as a general purpose post section which services the particular UART they are associated with. External clocks are input and internal clocks are output through these ports. Each of the four pins has a change of state detector which will signal a change (0 to 1 or 1 to 0) at the pin. The change of state detectors are individually enabled and may be set to cause and interrupt. These pins will normally be used for flow control hand-shaking and the interface to a modem. Their control is further described in I/O Ports section and the I/OPCR register.
Interrupt Control
The interrupt system determines when an interrupt should be asserted thorough an arbitration (or bidding) system. This arbitration is exercised over the several systems within the OCTART that may generate an interrupt. These will be referred to as "interrupt sources". There are 64 in all. In general the arbitration is based on the fill level of the receiver FIFO or the empty level of the transmitter FIFO. The FIFO levels are encoded into a four bit number which is concatenated to the channel number and source identification code. All of this is compared (via the bidding or arbitration process) to a user defined "threshold". When ever a source exceeds the numerical value of the threshold the interrupt will be generated. At the time of interrupt acknowledge (IACKN) the source which has the highest bid (not necessarily the source that caused the interrupt to be generated) will be captured in a "Current Interrupt Register" (CIR). This register will contain the complete definition of the interrupting source: channel, type of interrupt (receiver, transmitter, change of state, etc.), and FIFO fill level. The value of the bits in the CIR are used to drive the interrupt vector and global registers such that controlling processor may be steered directly to the proper service routine. A single read operation to the CIR provides all the information needed to qualify and quantify the most common interrupt sources. The interrupt sources for each channel are listed below.
DETAILED DESCRIPTIONS RECEIVER AND TRANSMITTER
The Octal UART has eight full-duplex asynchronous receiver/transmitters. The operating frequency for the receiver and transmitter can be selected independently from the baud rate generator, the counter , or from an external input. Registers that are central to basic full-duplex operation are the mode registers (MR0, MR1 and MR2), the clock select registers (RxCSR and TxCSR), the command register (CR), the status register (SR), the transmit holding register (TxFIFO), and the receive holding register (RxFIFO).
Transmitter
The transmitter accepts parallel data from the CPU and converts it to a serial bit stream on the TxD output pin. It automatically sends a start bit followed by the programmed number of data bits, an optional parity bit, and the programmed number of stop bits. The least significant bit is sent first. Each character is always "framed" by a single start bit and a stop bit that is 9/16 bit time or longer. If a new character is not available in the TxFIFO, the TxD output remains high, the "marking" position, and the TxEMT bit in the SR is set to 1. Transmitter Status Bits The SR (Status Register, one per UART) contains two bits that show the condition of the transmitter FIFO. These bits are TxRDY and TxEMT. TxRDY means the TxFIFO has space available for one or more bytes; TxEMT means The TxFIFO is completely empty and the last stop bit has been completed. TxEMT can not be active without TxRDY also being active. These two bits will go active upon initial enabling of the transmitter. They will extinguish on the disable or reset of the transmitter. Transmission resumes and the TxEMT bit is cleared when the CPU loads at least one new character into the TxFIFO. The TxRDY will not extinguish until the TxFIFO is completely full. The TxRDY bit will always be active when the transmitter is enabled and there is at lease one open position in the TxFIFO. The transmitter is disabled by reset or by a bit in the command register (CR). The transmitter must be explicitly enabled via the CR before transmission can begin. Note that characters cannot be 342
* Transmit FIFO empty level for each channel * Receive FIFO Fill level for each channel * Change in break received status for each channel * Receiver with error for each channel * Change of state on channel input pins * Receiver Watch-dog Time out Event * Xon/Xoff character recognition * Address character recognition
Associated with the interrupt system are the interrupt mask register (IMR) and the interrupt status register (ISR) resident in each UART. Programming of the IMR selects which of the above sources may enter the arbitration process. Only the bidders in the ISR whose associated bit in the IMR is set to one (1) will be permitted to enter the arbitration process. The ISR can be read by the host CPU to determine all currently active interrupting conditions. For convenience the bits of the ISR may be masked by the bits of the IMR. Whether the ISR is read unmasked or masked is controlled by the setting of bit 6 in MR1. Global Registers The "Global Registers", 19 in all, are driven by the interrupt system. These are not real hardware devices. They are defined by the 1995 May 1
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
loaded into the TxFIFO while the transmitter is disabled, hence it is necessary to enable the transmitter and then load the TxFIFO. It is not possible to load the TxFIFO and then enable the transmission. Note the difference between transmitter disable and transmitter reset. The transmitter may by reset by a hardware or software. The software reset is issued through command 3x of the Command register (CR). The disable is done by setting the transmitter disable bit also in the command register. If the transmitter is disabled, it continues operating until the character currently being transmitted, if any, is completely sent, including the stop bit. When reset the transmitter stops immediately, drives the transmitter serial data out put to a high level and discards any data in the TxFIFO. Transmission of "break" Transmission of a break character is often needed as a synchronizing condition in a data stream. The "break" is defined as a start bit followed by all zero data bits by a zero parity bit (if parity is enabled) and a zero in the stop bit position. The forgoing is the minimum time to define a break. The transmitter can be forced to send a break (continuous low condition) by issuing a start break command via the CR. This command does not have any timing associated with it. Once issued the TxD output will be driven low (the spacing condition) and remain there until the host issues a command to "stop break" via the CR or the transmitter is issued a software or hardware reset. In normal operation the break is usually much longer than one character time. 1x and 16x modes, Transmitter The transmitter clocking has two modes: 16x and 1x. Data is always sent at the 1x rate. However the logic of the transmitter may be operated with a clock that is 16 times faster than the data rate or at the same rate as the data i.e. 1x. All clocks selected internally for the transmitter (and the receiver) will be 16x clocks. Only when an external clock is selected may the transmitter logic and state machine operate in the 1x mode. The 1x or 16x clocking makes little difference in transmitter operation. (this is not true in the receiver) In the 16X clock mode the transmitter will recognize a byte in the TxFIFO within 1/16 to 2/16 bit time and thus begin transmission of the start bit; in the 1x mode this delay may be up to 2 bit times. Transmitter FIFO The transmitter buffer memory is a 16 byte by 8 bit ripple FIFO. The host writes characters to this buffer. This buffer accepts data only when the transmitter is enabled. The transmitter state machine reads them out in the order they were received and presents them to the transmitter shift register for serialization. The transmitter adds the required start, parity and stop bits as required the MR2 register programming. The start bit (always one bit time in length) is sent first followed by the least significant bit (LSB) to the most significant bit (MSB) of the character, the parity bit (if used) and the required stop bit(s). Logic associated with the FIFO encodes the number of empty positions available in a four bit value. This value is concatenated with the channel number and type interrupt type identifier and presented to the interrupt arbitration system. The encoding of the "positions empty" value is always 1 less than the number of available positions. Thus, an empty TxFIFO will bid with the value or 15; when full it will not bid at all; one position empty bids with the value 0. A full FIFO will not bid since a character written to it will be lost Normally a TxFIFO will present a bid to the arbitration system when ever it has one or more empty positions. The MR0[5:4] allow the 1995 May 1 343
user to modify this characteristic so that bidding will not start until one of four levels (empty, 3/4 empty, 1/2 empty, not full) have been reached. As will be shown later this feature may be used to make slight improvements in the interrupt service efficiency. A similar system exists in the receiver.
Receiver
The receiver accepts serial data on the RxD pin, converts the serial input to parallel format, checks for start bit, stop bit, parity bit (if any),framing error or break condition, and presents the assembled character and its status condition to the CPU via the RxFIFO. Three status bits are FIFOed with each character received. The RxFIFO is really 11 bits wide; eight data and 3 status. Unused FIFO bits for character lengths less than 8 bits are set to zero. It is important to note that receiver logic considers the entire message to be contained within the start bit to the stop bit. It is not aware that a message may contain many characters. The receiver returns to its idle mode at the end of each stop bit! As described below it immediately begins to search for another start bit which is normally, of course, immediately forth coming. 1x and 16x mode, Receiver The receiver operates in one of two modes; 1x and 16x. Of the two, the 16x is more robust and the preferred mode. Although the 1x mode may allow a faster data rate is does not provide for the alignment of the receiver 1x data clock to that of the transmitter. This strongly implies that the 1x clock of the remote transmitter is available to the receiver; the two devices are physically close to each other. The 16x mode operates the receiver logic at a rate 16 times faster than the 1x data rate. This allows for validation of the start bit, validation of level changes at the receiver serial data input (RxD), and a stop bit length as short as 9/16 bit time. Of most importance in the 16x mode is the ability of the receiver logic to align the phase of the receiver 1x data clock to that of the transmitter with an accuracy of less than 1/16 bit time. When the receiver is enabled ( via the CR register) it begins looking for a high to low (mark to space) transition on the RxD input pin. If a transition is detected, an internal counter running at 16 times the data rate is reset to zero. If the RxD remains low and is still low when the counter reaches a count of 7 the receiver will consider this a valid start bit and begin assembling the character. If the RxD input returns to a high state the receiver will reject the previous high to low (mark to space) transition on the RxD input pin. This action is the "validation" of the start bit and also establishes the phase of the receiver 1x clock to that of the transmitter The counter operating at 16x the data rate is the generator for the 1x data rate clock. With the phase of the receiver 1x clock aligned to the falling of the start bit (and thus aligned to the transmitter clock) AND with a valid start bit having been verified the receiver will continue receiving bits by sampling the RxD input on the rising edge of the 1x clock that is being generated by the above mentioned counter running 16 times the data rate. Since the falling edge of the 1x clock was aligned to falling edge of the start bit then the rising of the clock will be in the "center" of the bit cell. This action will continue until a full character has been assembled. Parity , framing, and stop bit , and break status is then assembled and the character and its status bits are loaded to the RxFIFO At this point the receiver has finished its task for that character and will immediately begin the search for another start bit. Receiver Status Bits There are five (5) status bits that are evaluated with each byte (or character) received: received break, framing error, parity error,
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
overrun error, and change of break. The first three are appended to each byte and stored in the RxFIFO. The last two are not necessarily related to the a byte being received or a byte that is in the RxFIFO. They are however developed by the receiver state machine . The "received break" will always be associated with a zero byte in the RxFIFO. It means that zero character was a break character and not a zero data byte. The reception of a break condition will always set the "change of break" (see below) status bit in the Interrupt Status Register(ISR). A framing error occurs when a non zero character was seen and that character has a zero in the stop bit position. The parity error indicates that the receiver generated parity was not the same as that sent by the transmitter. The overrun error occurs when the RxFIFO is full, the receiver shift register is full and another start bit is detected. At this moment the receiver has 17 valid characters and the start bit of the 18th has been seen. At this point the host has approximately 7/16 bit time to read a byte from the RxFIFO or the overrun condition will be set and the 18th character will overrun the 17th and the 19th the 18th and so on until an open position in the RxFIFO is seen. The meaning of the overrun is that data has been lost. Data in the RxFIFO remains valid. The receiver will begin placing characters in the RxFIFO as soon as a position becomes vacant. Note: Precaution must be taken when reading an overrun FIFO. There will be 16 valid characters. Data will begin loading as soon as the first character is read. The 17th. character will have been received as valid but it will not be known how many characters were lost between the two characters of the 16th. and 17th. reads of the RxFIFO The "Change of break" means that either a break has been detected or that the break condition has been cleared. This bit is available in the ISR. The beginning of a break will be signaled by the break change bit being set in the ISR AND the received break bit being set in the SR. At the termination of the break condition only the change of break in the ISR will be set. After the break condition is detected the termination of the break will only be recognized when the RxD input has returned to the high state for two successive edges of the 1x clock; 1/2 to 1 bit time. The receiver is disabled by reset or via CR commands. A disabled receiver will not interrupt the host CPU under any circumstance in the normal mode of operation. If the receiver is in the multi-drop or special mode, it will be partially enabled and thus may cause an interrupt. Refer to section on Wake-Up and minor modes and the register description for MR1 for more information. Receiver FIFO The receiver buffer memory is a 16 byte ripple FIFO with three status bits appended to each data byte. (The FIFO is then 16 11 bit "words"). The receiver state machine gathers the bits from the receiver shift register and the status bits from the receiver logic and writes the assembled byte and status bits to the RxFIFO. Logic associated with the FIFO encodes the number of filled positions for presentation to the interrupt arbitration system. The encoding is always 1 less than the number of filled positions. Thus, a full RxFIFO will bid with the value or 15; when empty it will not bit at all; one position occupied bids with the value 0. An empty FIFO will not bid since no character is available. Normally RxFIFO will present a bid to the arbitration system when ever it has one or more filled positions. The MR2[3:2 bits allow the user to modify this characteristic so that bidding will not start until one of four levels 1995 May 1 344
(one or more filled, 1/2 filled, 3/4 filled, full) have been reached. As will be shown later this feature may be used to make slight improvements in the interrupt service efficiency. A similar system exists in the transmitter. RxFIFO Status: Status reporting modes The description below applies to the upper three bits in the "Status Register" These three bits are not "in the status register"; They are part of the RxFIFO. The three status bits at the top of the RxFIFO are presented as the upper three bits of the status register included in each UART. The error status of a character , as reported by a read of the SR (status register upper three bits) can be provided in two ways, as programmed by the error mode control bit in the mode register: "Character mode " or the "Block Mode". The block mode may be further modified (via a CR command) to set the status bits as the characters enter the FIFO or as they are read from the FIFO. In the 'character' mode, status is provided on a character by character basis as the characters are read from the RxFIFO: the "status" applies only to the character at the top of the RxFIFO - The next character to be read In the 'block' mode, the status provided in the SR for these three bits is the logical OR of the status for all characters coming to the top of the RxFIFO, since the last reset error command was issued. In this mode each of the status bits stored in the RxFIFO are passed through a latch as they are sequentially read. If any of the characters has an error bit set then that latch will set and remain set until reset with an "Reset Error" command from the command register or a receiver reset. The purpose of this mode is indicating an error in the data block as opposed to an error in a character The latch used in the block mode to indicate "problem data" is usually set as the characters are read out of the RxFIFO. Via a command in the CR the latch may be configured to set the latch as the characters are pushed (loaded to) the RxFIFO. This gives the advantage of indicating "problem data" 16 characters earlier . In either mode, reading the SR does not affect the RxFIFO. The RxFIFO is 'popped' only when the RxFIFO is read. Therefore, the SR should be read prior to reading the corresponding data character. If the RxFIFO is full when a new character is received, that character is held in the receive shift register until a RxFIFO position is available. At this time there are 17 valid characters in the RxFIFO. If an additional character is received while this state exists, the contents of the RxFIFO are not affected: the character previously in the shift register is lost and the overrun error status bit, SR[4], will be set upon receipt of the start bit of the new (overrunning) character.
I/O ports
Each of the eight UARTs includes four I/O ports equipped with "change of state" detectors. The pins are individually programmable for an input only function or one of three output functions. These functions are controlled by the "I/O Port Configuration Register (I/OPCR)) They will normally be used for the RTSN-CTSN, DTR hardware signals, RxD or TxD input or output clocks or switch inputs as well as data out put from the I/OPIOR register. It is important to note that the input circuits are always active. That is the signal on a port, whether it is derived from an internal or external source is always available to the internal circuits associated with an input on that port. The "Change of State" (COS) detectors are sensitive to both a 1 to 0 or a 0 to 1 transition. The detectors are controlled by the internal
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
38.4 KHz baud rate and will signal a change when a transition has been stable for two rising edges of this clock. Thus a level on the I/O ports must be stable for 26 s to 52 s. Defining a port as an output will disable the COS detector at that port. The condition of the four I/O pins and their COS detectors is available at any time in the IPR (Input Port Register) The control of data and COS enable for these ports is through the I/OPIOR register. This is a read/write register and gives individual control to the enabling of the change of state detectors and also to the level driven by I/O pins when programmed to drive the logic level written to the four lower bits of the I/OPIOR. A read of this register will indicate the data on the pin at the time of the read and the state of the enabled COS detectors.
Multi-drop or Wake up or 9 bit mode This mode is used to address a particular UART among a group connected to the same serial data source. Normally it is accomplished by redefining the meaning of the parity bit such that it indicates a character as address or data. While this method is fully supported in the SC26C198 it also supports recognition of the character itself. Upon recognition of its address the receiver will be enabled and data pushed onto the RxFIFO. Further the Address recognition has the ability, if so programmed, to disable (not reset) the receiver when an address is seen that is not recognized as its own. The particular features of "Auto Wake and Auto Doze" are described in the detail descriptions below. Note: Care should be taken in the programming of the character recognition registers. Programming x'00, for example, may result in a break condition being recognized as a control character. This will be further complicated when binary data is being processed. Character Stripping The MR0 register provides for stripping the characters used for character recognition. Recall that the character recognition may be conditioned to control several aspects of the communication. However this system is first a character recognition system. The status of the various states of this system are reported in the XISR and ISR registers. The character stripping of this system allows for the removal of the specified control characters from the data stream: two for the Xon /Xoff and one for the wake up. Via control in the MR0 register these characters may be discarded (stripped) from the data stream when the recognition system "sees" them or they may be sent on the RxFIFO. Whether they are stripped or not the recognition will process them according to the action requested: flow control, wake up, interrupt generation, etc. Care should be exercised in programming the stripping option if noisy environments are encountered. If a normal character was corrupted to an Xoff character turned off the transmitter and it was then stripped, then the stripping action could make it difficult to determine the cause of transmitter stopping.
General Purpose Pins
In addition to the I/O ports for each UART four other ports are provided which service the entire chip. Two are dedicated as inputs and one as an output. The GIN1 and GIN0 are the input pins; GOUT0 the output. These ports are multiplexed to nearly every functional unit in the chip. See the registers which describe the multitude of connections available for these pins. The GOUT0 pin is highly multiplexed output and is controlled by four (4) registers: GPOSR, GPOR, GPOC and GPOD. The GIN0 and GIN1 pins are available to the receivers and transmitters, BRG counters and the GOUT0 pin.
Global Registers
The "Global Registers", 19 in all, are driven by the interrupt system. These are not real hardware devices. They are defined by the content of the CIR (Current Interrupt Register) as a result of an interrupt arbitration. In other words they are indirect registers pointed to by the content of the CIR. The list of global register follows: GIBCR The byte count of the interrupting FIFO GICR Channel number of the interrupting channel GITR Type identification of interrupting channel GRxFIFO Pointer to the interrupting receiver FIFO GTxFIFO Pointer to the interrupting transmitter FIFO A read of the GRxFIFO will give the content of the RxFIFO that presently has the highest bid value. The purpose of this system is to enhance the efficiency of the interrupt system. The global registers and the CIR update procedure are further described in the Interrupt Arbitration system
Interrupt Arbitration and IRQN generation
Interrupt arbitration is the process used to determine that an interrupt request should be presented to the host. The arbitration is carried out between the "Interrupt Threshold" and the "sources" whose interrupt bidding is enabled by the IMR. The interrupt threshold is part of the ICR (Interrupt Control Register) and is a value programmed by the user. The "sources" present a value to the interrupt arbiter. That value is derived from four fields: the channel number, type of interrupt source, FIFO fill level, and programmable value. . Only when one or more of these values exceeds the threshold value in the interrupt control register will the interrupt request (IRQN) be asserted. Following assertion of the IRQN the host will either assert IACKN(Interrupt Acknowledge) or will use the command to "Update the CIR". At the time either action is taken the CIR will capture the value of the source that is prevailing in the arbitration process. (Call this value the winning bid) The value in the CIR is the central quantity that results from the arbitration. It contains the identity of the interrupting channel, the type of interrupt in that channel (RxD, TxD, COS etc.) the fill levels of the RxD or TxD FIFOs and , in the case of an RxD interrupt an indicator of error data or good data. It also drives the Global Registers associated with the interrupt. Most importantly it drives the modification of the Interrupt Vector. The arbitration process is driven by the Sclk. It scans the 10 bits of the arbitration bus at the Sclk rate developing a value for the CIR 345
Character Recognition
The character recognition circuits are basically designed to provide general purpose character recognition. Additional control logic has been added to allow for Xon/Xoff flow control and for recognition of the address character in the multi-drop or "wake-up" mode. This logic also allows for the generation of an interrupts in either the general purpose recognition mode or the specific conditions mentioned above. Xon Xoff Characters The programming of these characters is usually done individually. However a method has been provided to write to all of registers in one operation. There are "Gang Load" and a "Gang Write" commands provided in the channel A Command Register. When these commands are executed all registers are programmed with the same characters. The "write" command loads a used defined character; the 'load" command loads the standard Xon/Xoff characters. Xon is x'11; Xoff x'13'. Any enabling of the Xon/Xoff functions will use the contents of the Xon and Xoff character registers as the basis on which recognition is predicated. 1995 May 1
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
every 22 Sclk cycles. New arbitration values presented to the arbitration block during an arbitration cycle will be evaluated in the next arbitration cycle. For sources other than receiver and transmitters the user may set the high order bits of an interrupt source's bid value, thus tailoring the relative priority of the interrupt sources. The priority of the receivers and transmitters is controlled by the fill level of their respective FIFOs. The more filled spaces in the RxFIFO the higher the bid value; the more empty spaces in the TxFIFO the higher its priority. Channels whose programmable high order bits are set will be given interrupt priority higher than those with zeros in their high order bits , thus allowing increased flexibility. The transmitter and receiver bid values contain the character counts of the associated FIFOs as high order bits in the bid value. Thus, as a receiver's RxFIFO fills, it bids with a progressively higher priority for interrupt service. Similarly, as empty space in a transmitter's TxFIFO increases, its interrupt arbitration priority increases. IACKN Cycle, Update CIR When the host CPU responds to the interrupt, it will usually assert the IACKN signal low. This will cause the OCTART to generate an IACKN cycle in which the condition of the interrupting device is determined. When IACKN asserts, the last valid interrupt number is captured in the CIR. The value captured presents most of the important details of the highest priority interrupt at the moment the IACKN (or the "Update CIR" command) was asserted. The Octal UART will respond to the IACKN cycle with an interrupt vector. The interrupt vector may be a fixed value, the content of the Interrupt Vector Register, or ,when "Interrupt Vector Modification is enabled via ICR, it may contain codes for the interrupt type and/or interrupting channel. This allows the interrupt vector to steer the interrupt service directly to the proper service routine. The interrupt value captured in the CIR remains until another IACKN cycle occurs or until an "Update CIR" command is given to the OCTART. The interrupting channel and interrupt type fields of the CIR set the current "interrupt context" of the OCTART. The channel component of the interrupt context allows the use of Global Interrupt Information registers that appear at fixed positions in the register address map. For example, a read of the Global RxFIFO will read the channel B RxFIFO if the CIR interrupt context is channel b receiver. At another time read of the GRxFIFO may read the channel D RxFIFO (CIR holds a channel D receiver interrupt) and so on. Global registers exist to facilitate qualifying the interrupt parameters and for writing to and reading from FIFOs without explicitly addressing them. The CIR will load with x'00 if IACKN or Update CIR is asserted when the arbitration circuit is NOT asserting and interrupt. In this condition there is no arbitration value that exceeds the threshold value. Polling Many users prefer polled to interrupt driven service where there are a large number of fast data channels and/or the host CPU's other interrupt overhead is low. The Octal UART is functional in this environment. The most efficient method of polling is the use of the "update CIR" command (with the interrupt threshold set to zero) followed by a read of the CIR. This dummy write cycle will perform the same CIR capture function that an IACKN falling edge would accomplish in an interrupt driven system. A subsequent read of the CIR, at the same address, will give information about an interrupt, if any. If the CIR contains 0s, no interrupt is awaiting service. If the value is non-zero, the fields of the CIR may be decoded for type, channel 1995 May 1 346
and character count information. Optionally, the global interrupt registers may be read for particular information about the interrupt status or use of the global RxD and TxD registers for data transfer as appropriate. The interrupt context will remain in the CIR until another update CIR command or an IACKN cycle is initiated by the host CPU occurs. The CIR loads with x'00 if Update CIR is asserted when the arbitration circuit has NOT detected arbitration value that exceeds the threshold value. Traditional methods of polling status registers may also be used. They of course are less efficient but give the most variable and quickest method of changing the order in which interrupt sources are evaluated and interrogated. Enabling and Activating Interrupt sources An interrupt source becomes enabled when its interrupt capability is set by writing to the Interrupt Mask Register, IMR. An interrupt source can never generate an IRQN or have its "bid" or interrupt number appear in the CIR unless the source has been enabled by the appropriate bit in an IMR. An interrupt source is active if it is presenting its bid to the interrupt arbiter for evaluation. Most sources have simple activation requirements. The watch-dog timer, break received, Xon/Xoff or Address Recognition and change of state interrupts become active when the associated events occur and the arbitration value generated thereby exceeds the threshold value programmed in the ICR (Interrupt Control Register). The transmitter and receiver functions have additional controls to modify the condition upon which the initiation of interrupt "bidding" begins: the TxINT and RxINT fields of the MR0 and MR2 registers. These fields can be used to start bidding or arbitration when the RxFIFO is not empty, 50% full, 75% full or 100% full. For the transmitter it is not full, 50% empty, 75% empty and empty. Example: To increase the probability of transferring the contents of a nearly full RxFIFO, do not allow it to start bidding until 50% or 75% full. This will prevent its relatively high priority from winning the arbitration process at low fill levels. A high threshold level could accomplish the same thing, but may also mask out low priority interrupt sources that must be serviced. Note that for fast channels and/or long interrupt latency times using this feature should be used with caution since it reduces the time the host CPU has to respond to the interrupt request before receiver overrun occurs. Setting Interrupt Priorities The bid or interrupt number presented to the interrupt arbiter is composed of character counts, channel codes, fixed and programmable bit fields. The interrupt values are generated for various interrupt sources as shown in the table below: The value represented by the bits 9 to 3 in the table below are compared against the value represented by the "Threshold. The "Threshold" ,bits 6 to 0 of the ICR (Interrupt Control Register), is aligned such that bit 6 of the threshold is compared to bit 9 of the interrupt value generated by any of the sources. When ever the value of the interrupt source is greater than the threshold the interrupt will be generated. The channel number arbitrates only against other channels. The threshold is not used for the channel arbitration. This results in channel D having the highest arbitration number. The decreasing order is H to A. If all other parts of an arbitration are equal then the channel number will determine which channel will dominate in the arbitration process .
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAA A A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA A AAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AA A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA A A AAAAAAAAAAAAA AA AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AA AA A
Table 1. Interrupt Arbitration Priority
Type B9 Receiver w/o error Receiver w/ error Transmitter Change of Break Change of State Xon/Xoff B8 B7 B6 B5 B4 B3 Bits 2:0 RxFIFO Byte Count -1 RxFIFO Byte Count -1 0 Programmed Field Programmed Field Programmed Field Programmed Field 0 1 0 1 1 0 0 0 0 1 1 1 1 1 1 0 0 0 1 1 Channel No Channel No Channel No Channel No Channel No Channel No Channel No Channel No 000 TxFIFO Byte Count -1 0 0 0 0 Address Recognition Receiver Watch-dog Threshold RxFIFO Byte Count -1 As RxFIFO Above Bits 6:0 of Interrupt Control Register Note several characteristics of the above table in bits 6:3. These bits contain the identification of the bidding source as indicated below: x001 Receiver without error x101 Receiver with error xx00 Transmitter 0010 Change of Break 0110 Change of State on I/O Ports 0111 Xon/Xoff Event 0011 Address Recognition the DSR (Data Set Ready) signal from the modem. In this case its arbitration value should be high. Once the DSR is recognized then its arbitration value could be reduced or turned off. The codes form bits 6:3 drive part of the interrupt vector modification and the Global Interrupt Type Register. The codes are unique to each source type and Identify them completely. The channel numbering progresses from "a" to "d" as the binary numbers 000 to 011 and identify the interrupting channel uniquely. As the channels arbitrate "d" will have the highest bidding value and "a" the lowest Note that the transmitter byte count is off-set from that of the receiver by one bit. This is to give the receiver more authority in the arbitration since and over-run receiver corrupts the message but an under-run transmitter is not harmful. This puts some constraints on how the threshold value is selected. If a threshold is chosen that has its MSB set to one then a transmitter can never generate an interrupt! Of course the counter point to this is the desire to set the interrupt threshold high so interrupts occur only when a maximum or near maximum number of characters may be transferred. To give some control over this dilemma control bits have been provided in the MR0 and MR2 registers of each channel to individually control when a receiver or transmitter may interrupt. The use of these bits will prevent a receiver or a transmitter from entering the arbitration process even though its FIFO fill level is above that indicated by the threshold value set. The bits in the MR0 and MR2 register are named TxINT (MR0[5:4]) and RxINT (MR2[3:2]) The watch-dog is included in the table above to show that it affects the arbitration. It does not have an identity of its own. A barking watch-dog will prevent any other source type from entering the arbitration process except enabled receivers. The threshold is effectively set to zero when any watch-dog times out. The receivers arbitrate among them selves and the one with the highest fill level will win the process. Note that the receiver wining the bid may not be the one that caused the watch-dog to bark. The fields labeled "Programmed Field" are the contents of the Bidding Control Registers, BCRs, for these sources. Setting these bits to high values can elevate the interrupt importance of the sources they represent to values almost as high as a full receiver. For example a COS event may be very important when it represents 1995 May 1 347 There is a single arbiter interrupt number that is not associated with any of the UART channels. It is the "Threshold Value" and is comprised of 7 bits from the Interrupt Control Register, ICR, and three zeros in the channel field. It is only when one or more of the enabled interrupt sources generates a arbitration value larger than the threshold value that the IRQN will be asserted. When the threshold bidding value is larger than any other bidding value then the IRQN will be withdrawn. In this condition the CIR will be loaded with if the IRQN or "Update CIR" command is asserted. Because the channels are numbered from 0 to 3 ( A to D) channel 3 will win the bid when all other parts of the bid are equal. Note: Based on this coding for the receiver and transmitter, a transmitter would not win a bid in the situation where the Count Field = 0 unless the threshold value is equal or less than 0000011. A single empty slot is left in the TxFIFO or a single filled slot in the RxFIFO will bid with a value of zero.
MODES OF OPERATION Major Modes
Four major modes of operation (normal, auto echo, local loop back and remote loop back) are provided and are controlled by MR2[7:6]. Three of these may be considered diagnostic. See the MR2 register description. The normal mode is the usual mode for data I/O operation. Most reception and transmission will use the normal mode. In the auto echo mode, the transmitter automatically re-transmits any character captured by the channel's receiver. The receiver 1x clock is used for the transmitter. This mode returns the received data back to the sending station one bit time delayed from its departure. Receiver to host communication is normal. Host to transmitter communication has no meaning. In the local loop back mode (used for diagnostic purposes) the transmitter is internally connected to the receiver input. The transmitter 1x clock used for the receiver. The RxD input pin is ignored and the transmitter TxD output pin is held high. This configuration allows the transmitter to send data to the receiver without any external parameters to affect the transmission of data. All status bits, interrupt conditions and processor interface operate normally. It is recommended that this mode be used when initially verifying processor to UART interface. The communication between the transmitter and receiver is entirely within the UART - it is essentially "talking to itself".
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
The remote loop back mode (also used for diagnostic purposes) is similar to auto echo except that the characters are not sent to the local CPU, nor is the receiver status updated. The received data is sent directly to the transmitter where it is sent out on the TxD output. The received data is not sent to the receive FIFO and hence the host will not normally be participating in any diagnostics.
associated with address recognition, data handling, receiver enables and disables. In both modes the meaning of the parity bit is changed. It is often referred to as the A/D bit or the address/data bit. It is used to indicate whether the byte presently in the receiver shift register is an "address" byte or a "data" byte. "1" usually means address; "0" data. Its purpose is to allow several receivers connected to the same data source to be individually addressed. Of course addressing could be by group also. Normally the "Master" would send an address byte to all receivers "listening" The receiver would then recognize its address and enable itself receiving the following data stream. Upon receipt of an address not its own it would then disable itself. As descried below appropriate status bits are available to describe the operation. Enabling the Wake Up mode This mode is selected by programming bits MR1[4:3] to '11'. The sub modes are controlled by bits 6, 1, 0 in the MR0 register. Bit 6 controls the loading of the address byte to the RxFIFO and MR0[1:0] determines the sub mode as shown in the following table. MR0[1:0] = 00 Normal Wake Up Mode (default). Host controls operation via interrupts and commands written to the command register (CR). Auto wake. Enable receiver on address recognition for this station. Upon recognition of its assigned address, in the Auto Wake mode, the local receiver will be enabled and normal receiver communications with the host will be established. Auto Doze. Disable receiver on address recognition, not for this station. Upon recognition of an address character that is not its own, in the Auto Doze mode, the receiver will be disabled and the address just received either discarded or pushed to the RxFIFO depending on the programming of MR0[6]. Auto wake and doze. Both modes above. The programming of MR0[1:0] to 11 will enable both the auto wake and auto doze features.
Minor Modes
The minor modes provide additional features within the major modes. In general the minor modes provide a reduction in the control burden and a less stringent interrupt latency time for the host processor. These modes could be invoked in all of the major modes.. However it may not be reasonable in many situations. Watch-dog Timer Time-out Mode Each receiver in the Octal UART is equipped with a watch-dog timer that is enabled by the "Watch-dog Timer Enable Register (WTER). The watch-dog "barks" (times out) if 64 counts of the receiver clock (64 bit times) elapse with no RxFIFO activity. RxFIFO events are a read of the RxFIFO or GRxFIFO, or the push of a received character into the RxFIFO. The timer resets when the (G)RxFIFO is read or if another character is pushed into the RxFIFO. The receiver watch-dog timer is included to allow detection of the very last character(s) of a received message that may be waiting in the RxFIFO, but are too few in number to successfully initiate an interrupt. The watch-dog timer is enabled for counting if the channel's bit in the Watch Dog Timer Control Register (WDTCR) is set. Note: a read of the GRxFIFO will reset the watch-dog timer of only the channel specified in the current interrupt context. Other watch-dogs are unaffected. The watch-dog timer may generate an input to the interrupt arbiter if IMR[6] is set. The status of the Watch-dog timer can be seen as Bit 6 of the Interrupt Status Register, ISR[6]. When a Watch-dog timer that is programmed to generate an interrupt times out it enters the arbitration process. It will then only allow receivers to enter the enter the arbitration. All other sources are bidding sources are disabled. The receivers arbitrate only amongst themselves.. The receiver only interrupt mode of the interrupt arbiter continues until the last watch-dog timer event has been serviced. While in the receiver only interrupt mode, the control of the interrupt threshold level is also disabled. The receivers arbitrate only between themselves. The threshold value is ignored. The receiver with the most FIFO positions filled will win the bid. Hence the user need not reduce the bidding threshold level in the ICR to see the interrupt from a nearly empty RxFIFO that may have caused the watch-dog time-out. Note: When any watch-dog times our only the receivers arbitrate. There is no increase in the probability of receiver being serviced causing the overrun of another receiver since they will still have priority based upon received character count. The interrupt will be cleared automatically upon the push of the next character received or when the RxFIFO or GRxFIFO is read. The ICR is unaffected by the watch-dog time-out interrupt and normal interrupt threshold level sensing resumes after the last watch-dog timer event has been processed. If other interrupt sources are active, the IRQN pin may remain low. Wake Up Mode The SC26C198 provides two modes of this common asynchronous "party line" protocol: the new automatic mode with 3 sub modes and the default Host operated mode. The automatic mode has several sub modes (see below). In the full automatic the internal state machine devoted to this function will handle all operations 1995 May 1 348
MR0[1:0] = 01
MR0[1:0] = 10
MR0[1:0] = 11
The enabling of the wake-up mode executes a partial enabling of the receiver state machine. Even though the receiver has been reset the wake up mode will over ride the disable and reset condition. Normal Wake up (The default configuration) In the default configuration for this mode of operation, a 'master' station transmits an address character followed by data characters for the addressed 'slave' station. The slave stations, whose receivers are normally disabled (not reset), examine the received data stream and interrupts the CPU (by setting RxRDY) only upon receipt of an address character. The CPU (host) compares the received address to its station address and enables the receiver if it wishes to receive the subsequent data characters. Upon receipt of another address character, the CPU may disable the receiver to initiate the process again . A transmitted character consists of a start bit, the programmed number of data bits, an address/data (A/D) bit, and the programmed number of stop bits. The polarity of the transmitted A/D bit is selected by the CPU by programming bit MR1[2]. MR1[2] = 0 transmits a zero in the A/D bit position which identifies the corresponding data bits as data. MR1[2] = 1 transmits a one in the A/D bit position which identifies the corresponding data bits as an address. The CPU should program the mode register prior to loading the corresponding data bytes into the TxFIFO.
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
While in this mode, the receiver continuously looks at the received data stream, whether it is enabled or disabled. If disabled, it sets the RxRDY status bit and loads the character into the RxFIFO if the received A/D bit is a one, but discards the received character if the received A/D bit is a zero. If the receiver is enabled, all received characters are transferred to the CPU via the RxFIFO. In either case, the data bits are loaded into the data FIFO while the A/D bit is loaded into the status FIFO position normally used for parity error (SR[5]). Framing error, overrun error, and break detect operate normally whether or not the receiver is enabled. Automatic operation, Wake Up & Doze The automatic configuration for this mode uses on-board comparators to examine incoming address characters. Each UART channel may be assigned a unique address character. See the address register map and the description of the Address Recognition Character Register (ARCR). The device may be programmed to automatically awaken a sleeping receiver and/or disable an active receiver based upon address characters received. The operation of the basic receiver is the same as described above for the default mode of wake-up operation except that the CPU need not be interrupted to make a change in the receiver status. Three bits in the Mode Register 0, (MR0), control the address recognition operation. MR0[6] controls the RxFIFO operation of the received character; MR0[1:0] controls the wake up mode options. If MR0[6] is set the address character will be pushed onto the RxFIFO, otherwise the character will be discarded. (The charter is stripped from the data stream) The MR0[1:0] bits set the options as follows: A b'00 in this field, the default or power-on condition, puts the device in the default (CPU controlled) wake up mode of operation as described above. The auto-wake mode, enabled if MR0[0] is set, will cause the dedicated comparators to examine each address character presented by the receiver. If the received character matches the reference character in ARCR, the receiver will be enabled and all subsequent characters will be FIFOed until another address event occurs or the host CPU disables the receiver explicitly. The auto doze mode, enabled if MR0[1] is set, will automatically disable the receiver if an address is received that does not match the reference character in the ARCR. The UART channel can present the address recognition event to the interrupt arbiter for IRQN generation. The IRQN generation may be masked by setting bit 5 of the Interrupt Mask Register, IMR. The bid level of an address recognition event is controlled by the Bidding Control Register, BCRA, of the channel. Note: To ensure proper operation, the host CPU must clear any pending Address Recognition interrupt before enabling a disabled receiver operating in the Special or Wake-up mode. This may be accomplished via the CR commands to clear the Address Interrupt or by resetting the receiver. Xon/Xoff Operation Receiver Mode Since the receiving FIFO resources in the Octal UART are limited, some means of controlling a remote transmitter is desirable in order to lessen the probability of receiver overrun. The Octal UART provides two methods of controlling the data flow. A hardware assisted means of accomplishing control, the so-called out-of-band flow control, and an in-band flow control method. The out-of-band flow control is implemented through the CTSN-RTSN signaling via the I/O ports. The operation of these hardware handshake signals is described in the receiver and transmitter discussions. 1995 May 1 349
In-band flow control is a protocol for controlling a remote transmitter by embedding special characters within the message stream, itself. Two characters, Xon and Xoff, which do not represent normal printable characters take on flow control definitions when the Xon/Xoff capability is enabled. Flow control characters received may be used to gate the channel transmitter on and off. This activity is referred to as Auto-transmitter mode. To protect the channel receiver from overrun, fixed fill levels (hardware set at 12 characters) of the RxFIFO may be employed to automatically insert Xon/Xoff characters in the transmitter's data stream. This mode of operation is referred to as auto-receiver mode. Commands issued by the host CPU via the CR can simulate all these conditions. Auto-transmitter mode When a channel receiver pushes an Xoff character into the RxFIFO, the channel transmitter will finish transmission of the current character and then stop transmitting. A transmitter so idled can be restarted by the receipt of an Xon character by the receiver, or by a hardware or software reset. The last option results in the loss of the un-transmitted contents of the TxFIFO. When operating in this mode the Command Register commands for the transmitter are not effective. While idle data may be written to the TxFIFO and it continues to present its fill level to the interrupt arbiter and maintains the integrity of its status registers. Use of '00' as an Xon/Xoff character is complicated by the Receiver break operation which pushes a '00' character on the RxFIFO. The Xon/Xoff character detectors do not discriminate this case from an Xon/Xoff character received through the RxD pin. Note: To be recognized as an Xon or Xoff character, the receiver must have room in the RxFIFO to accommodate the character. An Xon/Xoff character that is received resulting in a receiver overrun does not effect the transmitter nor is it pushed into the RxFIFO, regardless of the state of the Xon/Xoff transparency bit, MR0(7). Note: Xon /Xoff characters The Xon/Xoff characters with errors will be accepted as valid. The user has the option sending or not sending these characters to the FIFO. Error bits associated with Xon/Xoff will be stored normally to the receiver FIFO. The channel's transmitter may be programmed to automatically transmit an Xoff character without host CPU intervention when the RxFIFO fill level exceeds a fixed limit (12). In this mode, it will conversely transmit an Xon character when the RxFIFO level drops below a second fixed limit (8). A character from the TxFIFO that has been loaded into the TxD shift register will continue to transmit. Character(s) in the TxFIFO that have not been popped are unaffected by the Xon or Xoff transmission. They will be transmitted after the Xon/Xoff activity concludes. If the fill level condition that initiates Xon activity negates before the flow control character can begin transmission, the transmission of the flow control character will not occur, i.e. either of the following sequences may be transmitted depending on the timing of the FIFO level changes with respect to the normal character times: Character Xoff Xon Character Character Character Hardware keeps track of Xoff characters sent that are not rescinded by an Xon. This logic is reset by writing MR0(3) to '0'. If the user drops out of Auto-receiver mode while the XISR shows Xon as the last character sent, the Xon/Xoff logic will not automatically send the negating Xon. Host mode When neither the auto-receiver nor auto-transmitter modes are set, the Xon/Xoff logic is operating in the host mode. In host mode, all
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
activity of the Xon/Xoff logic is initiated by commands to the CRx command forces the transmitter to disable exactly as though an Xoff character had been received by the RxFIFO. The transmitter will remain disabled until the chip is reset or the CR(7:3) = 10110 (Xoff resume) command is given. In particular, reception of an Xon or disabling or re-enabling the transmitter will NOT cause resumption of transmission. Redundant CRTXon/off commands, i.e. CRTXon CRTXon, are harmless, although they waste time. A CRTXon may be used to cancel a CRTXoff (and vice versa), but both may be transmitted depending on the timing with the transmit state machine. The kill CRTX command can be used to cleanly terminate any CRTX commands pending with the minimum impact on the transmitter. Note: In no case will an Xon/Xoff character transmission be aborted. Once the character is loaded into the TX Shift Register, transmission continues until completion or a chip reset is encountered. The kill CRTX command has no effect in either of the Auto modes. Mode control Xon/Xoff mode control is accomplished via the MR0. Bits 3 and 2 reset to zero resulting in all Xon/Xoff processing being disabled. If MR0[2] is set, the transmitter may be gated by Xon/Xoff characters received. If MR0[3] is set, the transmitter will transmit Xon and Xoff when triggered by attainment of fixed fill levels in the channel RxFIFO. The MR0[7] bit also has an Xon/Xoff function control. If this bit is set, a received Xon or Xoff character is not pushed into the RxFIFO. If cleared, the power-on and reset default, the received
Xon or Xoff character is pushed onto the RxFIFO for examination by the host CPU. The MR0(7) function operates regardless of the value in MR0(3:2) Xon/Xoff Interrupts The Xon/Xoff logic generates interrupts only in response to recognizing either of the characters in the XonCR or XoffCR (Xon or Xoff Character Registers). The transmitter activity initiated by the Xon/Xoff logic or any CR command does not generate an interrupt. The character comparators operate regardless of the value in MR0(3:2). Hence the comparators may be used as general purpose character detectors by setting MR0(3:2)='00' and enabling the Xon/Xoff interrupt in the IMR. The Octal UART can present the Xon/Xoff recognition event to the interrupt arbiter for IRQN generation. The IRQN generation may be masked by setting bit 4 of the Interrupt Mask Register, IMR. The bid level of an Xon/Xoff recognition event is controlled by the Bidding Control Register X, BCRX, of the channel. The interrupt status can be examined in ISR[4]. If cleared, no Xon/Xoff recognition event is interrupting. If set, an Xon or Xoff recognition event has been detected. The X Interrupt Status Register, XISR, can be read for details of the interrupt and to examine other, non-interrupting, status of the Xon/Xoff logic. Refer to the XISR in the Register Descriptions. The character recognition function and the associated interrupt generation is disabled on hardware or software reset .
1995 May 1
350
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
REGISTER DEFINITIONS
The operation of the Octal UART is programmed by writing control words into the appropriate registers. Operational feedback is provided via status registers which can be read by the host CPU. The Octal UART addressing is loosely divided, by the address bit A(7), into two parts: 1) That part which is concerned with the configuration of the chip interface and communication modes. This part controls the elements of host interface setup, interrupt arbitration, I/O Port Configuration that part of the UART channel
definitions that do not change in normal data handling. This section is listed in the "Register Map, Control". 2) That part concerned with the transmission and reception of the bit streams. This part concerns the data status, FIFO fill levels, data error conditions, channel status, data flow control (hand shaking). This section is listed in the "Register Map, Data". The Global Configuration Control Register (GCCR) sets the type of bus cycle, interrupt vector modification and the power up or down mode.
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A
Table 2. GCCR - Global Configuration Control Register
Bit 7 Bit 6 Bit 5:3 THIS IS A VERY IMPORTANT REGISTER! IT SHOULD BE THE FIRST REGISTER ADDRESSED DURING INITIALIZATION. Bit 2:1 Reserved Reserved Sync bus cycles Reserved Reserved Set to 0 IVC, Interrupt Vector Control Bit 0 Power Down Mode Must be set to 0 0 - async cycles 1 - Sync, non-pipe-lined cycle 00 - no interrupt vector 01 - IVR 10 - IVR + channel code 11 - IVR + interrupt type + channel code 0 - Device enabled 1 - Power down GCCR(7): This bit is reserved for future versions of this device. If not set to zero most internal addressing will be disabled! GCCR(6): Bus cycle selection Controls the operation of the host interface logic. If reset, the power on/reset default, the host interface can accommodate arbitrarily long bus I/O cycles. If the bit is set, the Octal UART expects four Sclk cycle bus I/O operations similar to those produced by an i80386 processor in non-pipelined mode. The major differences in these modes are observed in the DACKN pin function. In Sync mode, no negation of CEN is required between cycles. transmission/reception activities cease, and all processing for input change detection, BRG counter/timers and Address/Xon./Xoff recognition is disabled. Note: For maximum power savings it is recommended that all switching inputs be stopped and all input voltage levels be within 0.5 volt of the Vcc and Vss power supply levels. To switch from the asynchronous to the synchronous bus cycle mode, a single write operation to the GCCR, terminated by a negation of the CEN pin, is required. This cycle may be 4 cycles long if the setup time of the CEN edge to Sclk can be guaranteed. The host CPU must ensure that a minimum of two Sclk cycles elapse before the initiation of the next (synchronous) bus cycle(s). A hardware or software reset is recommended for the unlikely requirement of returning to the asynchronous bus cycling mode. GCCR(2:1): Interrupt vector configuration The IVC field controls if and how the assertion of IACKN (the interrupt acknowledge pin) will form the interrupt vector for the Octal UART. If b'00, no vector will be presented during an IACKN cycle. The bus will be driven high (xFF). If the field contains a b'01, the contents of the IVR, Interrupt Vector Register, will be presented as the interrupt vector without modification. If IVC = b'10, the channel code will replace the 3 LSBs of the IVR; if IVC = b'11 then a modified interrupt type and channel code replace the 5 LSBs of the IVR. Note: The modified type field IVR(4:3) is: 10 Receiver w/o error 11 Receiver with error 01 Transmitter 00 All remaining sources GCCR(0): Power down control Controls the power down function. During power down the internal oscillator is disabled, interrupt arbitration and all data
MR - Mode Registers
The user must exercise caution when changing the mode of running receivers, transmitters or BRG counter/timers. The selected mode will be activated immediately upon selection, even if this occurs during the reception or transmission of a character. It is also possible to disrupt internal controllers by changing modes at critical times, thus rendering later transmission or reception faulty or impossible. An exception to this policy is switching from auto-echo or remote loop back modes to normal mode. If the deselection occurs just after the receiver has sampled the stop bit (in most cases indicated by the assertion of the channel's RxRDY bit) and the transmitter is enabled, the transmitter will remain in auto-echo mode until the end of the transmission of the stop bit.
Table 3. MR0- Mode Register 0
Bit 7 Xon/Xoff * transparency
Bit 6
Bit 5:4
Bit 3:2
Bit 1:0
Address Recognition * transparency
TxiNT
In-band flow control mode
Address Recognition control 00 - none 01 - Auto wake 10 - Auto doze 11 - Auto wake and auto doze
0 - flow control characters received are pushed onto the RxFIFO 1 - flow control characters received are not pushed onto the RxFIFO
0 - Address characters received are pushed to RxFIFO
1 - Address characters received are not pushed onto the RxFIFO
TxFIFO interrupt level control 00 - empty 01 - 3/4 empty 10 - 1/2 empty 11 - not full
00 - host mode, only the host CPU may initiate flow control actions through the CR 01 - Auto Transmitter flow control 10 - Auto Receiver flow control 11 - Auto Receiver and Transmitter flow control
1995 May 1
351
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
* If these bits are not 0 the characters will be stripped regardless of bits (3:2) or (1:0) MR0[7:6] - Control the handling of recognized Xon/Xoff or Address characters. If set, the character codes are placed on the RxFIFO along with their status bits just as ordinary characters are. If the character is not pushed onto the RxFIFO, its received status will be lost unless the receiver is operating in the block error mode, see MR1[5] and the general discussion on receiver error handling. Interrupt processing is not effected by the setting of these bits. See Character recognition section. MR0[5:4] - Controls the fill level at which a transmitter begins to present its interrupt number to the interrupt arbitration logic. Use of a low fill level minimizes the number of interrupts generated and maximizes the number of transmit characters per interrupt cycle. It also increases the probability that the transmitter will go idle for lack of characters in the TxFIFO. MR0[3:2] - Controls the Xon/Xoff processing logic. Auto Transmitter flow control allows the gating of Transmitter activity by Xon/Xoff characters received by the Channel's receiver. Auto Receiver flow control causes the Transmitter to emit an Xoff
character when the RxFIFO has loaded to a depth of 12 characters. Draining the RxFIFO to a level of 8 or less causes the Transmitter to emit an Xon character. All transmissions require no host involvement. A setting other than b'00 in this field precludes the use of the command register to transmit Xon/Xoff characters. Note: Interrupt generation in Xon/Xoff processing is controlled by the IMR (Interrupt Mask Register) of the individual channels. The interrupt may be cleared by a read of the XISR, the Xon/Xoff Interrupt Status Register. Receipt of a flow control character will always generate an interrupt if the IMR is so programmed. The MR0[3:2] bits have effect on the automatic aspects of flow control only, not the interrupt generation. MR0[1:0] - This field controls the operation of the Address recognition logic. If the device is not operating in the special or "wake-up" mode, this hardware may be used as a general purpose character detector by choosing any combination except b'00. Interrupt generation is controlled by the channel IMR. The interrupt may be cleared by a read of the XISR, the Xon/Xoff Interrupt Status Register. See further description in the section on the Wake Up mode.
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A
Table 4. MR1 - Mode Register 1
Bit 7 Bit 6 RxRTS Control 0 - off 1 - on ISR Read Mode Bit 5 Bit 4:3 Bit 2 Bit 1:0 Error Mode Parity Mode Parity Type 0 = Even 1 = Odd Bits per Character 00 - 5 01 - 6 10 - 7 11 - 8 0 - ISR unmasked 1 - ISR masked 0 = Character 1 = Block 00 - With Parity 01 - Force parity 10 - No parity 11 - Special Mode MR1[7]: Receiver Request to Send Control This bit controls the deactivation of the RTSN output (I/O2) by the receiver. This output is asserted and negated by commands applied via the command register. MR1[7] = 1 causes RTSN to be automatically negated upon receipt of a valid start bit if the receiver FIFO is full or greater. RTSN is reasserted when an the FIFO fill level falls below full. This constitutes a change from previous members of Philips (Signets)' UART families where the RTSN function triggered on FIFO full. This behavior caused problems with PC UARTs that could not stop transmission at the proper time. . The RTSN feature can be used to prevent overrun in the receiver, by using the RTSN output signal, to control the CTSN input of the transmitting device. MR1[6]: Interrupt Status Masking This bit controls the readout mode of the Interrupt Status Register, ISR. If set, the ISR reads the current status masked by the IMR, i.e. only interrupt sources enabled in the IMR can ever show a '1' in the ISR. If cleared, the ISR shows the current status of the interrupt source without regard to the Interrupt Mask setting. MR1[5]: Error Mode Select This bit selects the operating mode of the three FIFOed status bits (FE, PE, received break). In the character mode, status is provided on a character by character basis; the status applies only to the character at. the bottom of the FIFO. In the block mode, the status provided in the SR for these bits is the accumulation (logical OR) of the status for all characters coming to the top of the FIFO, since the last reset error command was issued. MR1[4:3]: Parity Mode Select If 'with parity' or 'force parity' is selected, a parity bit is added to the transmitted character and the receiver performs a parity check on incoming data. MR1[4:3] = 11 selects the channel to operate in the special wake up mode. MR1[2]: Parity Type Select This bit sets the parity type (odd or even) if the 'with parity' mode is programmed by MR1[4:3], and the polarity of the forced parity bit if the 'force parity' mode is programmed. It has no effect if the 'no parity' mode is programmed. In the special 'wake up' mode, it selects the polarity of the A/D bit. The parity bit is used to an address or data byte in the 'wake up' mode. MR1[1:0]: Bits per Character Select This field selects the number of data bits per character to be transmitted and received. This number does not include the start, parity, or stop bits.
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A
Table 5. MR2 - Mode Register 2
Bits 7:6 The MR2 register provides basic channel setup control that may need more frequent updating. Bit 5 Bit 4 Channel Mode TxRTS Control 0 = No 1 = Yes CTSN Enable Tx 0 = No 1 = Yes RxINT Bit 3:2 Bit 1:0 Stop Length 00 = 1.0 01 = 1.5 10 = 2.0 11 = 9/16 00 = normal 01 = Auto echo 10 = Local loop 11 = Remote loop 00 = RRDY 01 = Half Full 10 = 3/4 Full 11 = Full 1995 May 1 352
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
MR2[7:6] - Mode Select The Octal UART can operate in one of four modes: MR2[7:6] = b'00 is the normal mode, with the transmitter and receiver operating independently. MR2[7:6] = b'01 places the channel in the automatic echo mode, which automatically re transmits the received data. The following conditions are true while in automatic echo mode: Received data is re-clocked and re-transmitted on the TxD output. The receive clock is used for the transmitter. The receiver must be enabled, but the transmitter need not be enabled. The TxRDY and TxEMT status bits are inactive. The received parity is checked, but is not regenerated for transmission, i.e., transmitted parity bit is as received. Character framing is checked, but the stop bits are re-transmitted as received. A received break is echoed as received until the next valid start bit is detected . CPU to receiver communication continues normally, but the CPU to transmitter link is disabled. Two diagnostic modes can also be selected. MR2[7:6] = b'10 selects local loop back mode. In this mode: The transmitter output is internally connected to the receiver input. The transmit clock is used for the receiver. The TxD output is held high. The RxD input is ignored. The transmitter must be enabled, but the receiver need not be enabled. CPU to transmitter and receiver communications continue normally. The second diagnostic mode is the remote loop back mode, selected by MR2[7:6] = b'11. In this mode: Received data is re-clocked and re-transmitted on the TxD output. The receive clock is used for the transmitter. Received data is not sent to the local CPU, and the error status conditions are inactive. The received parity is not checked and is not regenerated for transmission, i.e., the transmitted parity bit is as received. The receiver must be enabled, but the transmitter need not be enabled. Character framing is not checked, and the stop bits are re-transmitted as received. A received break is echoed as received until the next valid start bit is detected. MR2[5] - Transmitter Request to Send Control This bit controls the deactivation of the RTSN output (I/O2) by the transmitter. This output is manually asserted and negated by
appropriate commands issued via the command register. MR2[5] = 1 causes RTSN to be reset automatically one bit time after the characters in the transmit shift register and in the TxFIFO (if any) are completely transmitted (includes the programmed number of stop bits if the transmitter is not enabled). This feature can be used to automatically terminate the transmission of a message as follows: Program auto reset mode: MR2[5]= 1. Enable transmitter. Assert RTSN via command. Send message. After the last character of the message is loaded to the TxFIFO, disable the transmitter. Before disabling the transmitter be sure the Status Register TxEMT bit is NOT set (i.e., the transmitter is not underrun). The underrun condition is indicated by the TxEMT bit in the SR being set. The condition occurs immediately upon enabling the transmitter and persists until a character is loaded to the TxFIFO. The Underrun condition will not be a problem as long as the controlling processor keeps up with the transmitter data flow. The proper operation of this feature assumes that the transmitter is busy (not underrun) when the disable is issued. The last character will be transmitted and RTSN will be reset one bit time after the last stop bit. NOTE: When the transmitter controls the RTSN pin, the meaning of the pin is COMPLETELY changed. It has nothing to do with the normal RTSN/CTSN "handshaking". It is usually used to mean "end of message" and to "turn the line around" in simplex communications. MR2[4] - Clear to Send Control The state of this bit determines if the CTSN input (I/O0) controls the operation of the transmitter. If this bit is 0, CTSN has no effect on the transmitter. If this bit is a 1, the transmitter checks the state of CTSN each time it is ready to begin sending a character. If it is asserted (low), the character is transmitted. If it is negated (high), the TxD output remains in the marking state and the transmission is delayed until CTSN goes low. Changes in CTSN, while a character is being transmitted, do not affect the transmission of that character. This feature can be used to prevent overrun of a remote receiver. MR2[3:2] - RxINT control field Controls when interrupt arbitration for a receiver begins based on RxFIFO fill level. This field allows interrupt arbitration to begin when the RxFIFO is full, 3/4 full, 1/2 full or when it contains at least 1 character. MR2[1:0] - Stop Bit Length Select This field programs the length of the stop bit appended to the transmitted character. Stop bit lengths of 9/16, 1, 1.5 and 2 bits can be programmed for character lengths of 6, 7, and 8 bits. For a character length of 5 bits, 1, 1.5 and 2 stop bits can be programmed. In all cases, the receiver only checks for a mark condition at the center of the first stop bit position (one bit time after the last data bit, or after the parity bit if parity is enabled). If an external 1X clock is used for the transmitter, MR2[1] = 0 selects one stop bit and MR2[1] = 1 selects two stop bits to be transmitted.
Table 6. RxCSR and TxCSR - Receiver and Transmitter Clock Select Registers
AAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A
Both registers consist of single 5 bit field that selects the clock source for the receiver and transmitter, respectively. The unused bits in this register read b'111. The baud rates shown in the table below are based on the x1 crystal frequency of 3.6864MHz. The baud rates shown below will vary as the X1 crystal clock varies. For example, if the X1 rate is changed to 7.3728 MHz all the rates below will double. Bits 7:5 Bits 4:0 Reserved Transmitter/Receiver Clock select code, (see Clock Mux Table below) 353 1995 May 1
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA AAA AAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Table 7. Data Clock Mux
Clock Select Code 00000 00001 00010 00011 00100 00101 00110 00111 CCLK maximum rate is 8MHz. Data clock rates will follow exactly the ratio of CCLK to 3.6864MHz. Clock selection, CCLK = 3.6864 MHz BRG - 50 BRG - 75 Clock Select Code 10000 10001 10010 10011 10100 10101 10110 10111 Clock selection, CCLK = 3.6864 MHz BRG - 19.2K BRG - 28.2K BRG - 38.4K BRG - 57.6K BRG - 150 BRG - 200 BRG - 300 BRG - 450 BRG - 600 BRG - 900 BRG - 115.2K GIN0 GIN1 BRG - 230.4K 01000 01001 01010 01011 01100 01101 01110 01111 BRG - 1200 BRG - 1800 BRG - 2400 BRG - 3600 BRG - 4800 BRG - 7200 BRG - 9600 11000 11001 11010 11011 11100 11101 11110 11111 BRG C/T 0 BRG C/T 1 Reserved I/O2 rcvr, I/O3 xmit -16x I/O2 rcvr, I/O3 xmit-1x Reserved Reserved Reserved BRG - 14.4K
Table 8. CR - Command Register
Bits 7:3 Bit 2
CR is used to write commands to the Octal UART. Bit 1 Channel Command codes see "Command Register Table"
Bit 0
Lock TxD and RxFIFO enables
Enable Tx
Enable Rx
CR[2] - Lock TxD and RxFIFO enables If set, the transmitter and receiver enable bits, CR[1:0] are not significant. The enabled/disabled state of a receiver or transmitter can be changed only if this bit is at zero during the time of the write to the command register. WRITES TO THE UPPER BITS OF THE CR WOULD USUALLY HAVE CR[2] AT 1 to maintain the condition of the receiver and transmitter. The bit provides a mechanism for writing commands to a channel, via CR[7:3], without the necessity of keeping track of or reading the current enable status of the receiver and transmitter. CR[1] - Enable Transmitter A one written to this bit enables operation of the transmitter. The TxRDY status bit will be asserted. When disabled by writing a zero to this bit, the command terminates transmitter operation and resets the TxRDY and TxEMT status bits. However, if a character is being transmitted or if characters are loaded in the TxFIFO when the transmitter is disabled, the transmission of the all character(s) is completed before assuming the inactive state. CR[0] - Enable Receiver A one written to this bit enables operation of the receiver. If not in the special wake up mode, this also forces the receiver into the search for start bit state. If a zero is written, this command terminates operation of the receiver immediately - a character being received will be lost. The command has no effect on the receiver status bits or any other control registers. If the special wake-up mode is programmed, the receiver operates even if it is disabled (see Wake-up Mode). CR[7:3] - Miscellaneous Commands ( See Table below)
The encoded value of this field can be used to specify a single command as follows: 00000 No command. 00001 Reserved 00010 Reset receiver. Resets the receiver as if a hardware reset had been applied. The receiver is disabled and the FIFO pointer is reset to the first location effectively discarding all unread characters in the FIFO. 00011 Reset transmitter. Resets the transmitter as if a hardware reset had been applied. 00100 Reset error status. Clears the received break, parity error, framing error, and overrun error bits in the status register (SR[7:4]). Used in character mode to clear overrun error status (although RB, PE and FE bits will also be cleared), and in block mode to clear all error status after a block of data has been received. 00101 Reset break change interrupt. Causes the break detect change bit in the interrupt status register (ISR[2]) to be cleared to zero. 00110 Start break. Forces the TxD output low (spacing). If the transmitter is empty, the start of the break condition will be delayed up to two bit times. If the transmitter is active, the break begins when transmission of the current character is completed. If there are characters in the TxFIFO, the start of break is delayed until those characters, or any others loaded after it have been transmitted (TxEMT must be true before break begins). The transmitter must be enabled to start a break. 00111 Stop break. The TxD line will go high (marking) within two bit times. TxD will remain high for one bit time before the next character, if any, is transmitted. 01000 Assert RTSN. Causes the RTSN output to be asserted (low). 01001 Negate RTSN. Causes the RTSN output to be negated (high). Note: The two commands above actually reset and set, respectively, the I/O2 or I/O1 pin associated with the I/OPIOR register. 01010 Reserved 01011 Reserved 01100 Reserved
1995 May 1
354
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
01101
01111 10000 10001 10010
10011
Block error status mode. Upon reset of the device or an individual receiver, the block mode of receiver error status accumulates as each character moves to the bottom of the RxFIFO, the position from which it will be read. In this mode of operation, the RxFIFO may contain a character with non-zero error status for some time. The status will not reflect the error character's presence until it is ready to be popped from the RxFIFO. Command 01101 allows the error status to be updated as each character is pushed into the RxFIFO. This allows the earliest detection of a problem character, but complicates the determination of exactly which character is causing the error. This mode of block error accumulation may be exited only by resetting the chip or the individual receiver. Reserved. Transmit an Xon Character Transmit an Xoff Character Reserved for channels b-h, for channel a: enables a Gang Write of Xon Character Registers. After this command is issued, a write to the channel A Xon Character Register will result in a write to all channel's Xon character registers. This command provides a mechanism to initialize all the Xon Character registers with one write. A write to channel A Xon Character Register returns the Octal UART to the individual Xon write mode. Reserved for channels b-h, for channel a: enables Gang Write of Xoff Character Registers. After this command is issued, a write to the channel A Xoff Character Register will result in a write to all channel's Xoff character registers. This command provides a mechanism to initialize all the Xoff Character registers with one write. A write to channel A Xoff Character Register returns the Octal UART to the individual Xoff write mode.
Note: Gang writing of Xon/Xoff Character Commands: Issuing command causes the next write to Xon/Xoff Character Register A to effect a simultaneous write into the other 3 Xon/Xoff character registers. After the Xon/Xoff Character Register A is written, the 26C198 returns to individual write mode for the Xon/Xoff Character Registers. Other intervening reads and writes are ignored. The device resets to individual write mode. 10100 Reserved for channels b-h, for channel a: executes a Gang Load of Xon Character Registers. Executing this command causes a write of the value x'11 to all channel's Xon character registers. This command provides a
mechanism to initialize all the Xon Character registers to a default value with one write. Execution of this command is immediate and does not effect the timing of subsequent host I/O operations. 10101 Reserved for channels b-h, for channel a: executes a Gang Load of Xoff Character Registers. Executing this command causes a write of the value x'13 to all channel's Xoff character registers. This command provides a mechanism to initialize all the Xoff Character registers to a default value with one write. Execution of this command is immediate and does not effect the timing of subsequent host I/O operations. 10110 Xoff resume command (CRXoffre; not active in "Auto-Transmit Mode"). A command to cancel a previous Host Xoff command. Upon receipt, the channel's transmitter will transfer a character, if any, from the TxFIFO and begin transmission. 10111 Host Xoff command (CRXoff). This command allows tight host CPU control of the flow control of the channel transmitter. When interrupted for receipt of an Xoff character by the receiver, the host may stop transmission of further characters by the channel transmitter by issuing the Host Xoff command. Any character that has been transferred to the TxD shift register will complete its transmission, including the stop bit. 11000 Cancel Host transmit flow control command. Issuing this command will cancel a previous transmit command if the flow control character is not yet loaded into the TxD Shift Register. If there is no character waiting for transmission or if its transmission has already begun, then this command has no effect. 11001-11011 Reserved 11011 Reset Address Recognition Status. This command clears the interrupt status that was set when an address character was recognized by a disabled receiver operating in the special mode. 11100-11101 Reserved 11110 Resets all UART channel registers. This command provides a means to zero all the UART channels that are not reset to x'00 by a reset command or a hardware reset. 11111 Reserved for channels b-h, for channel a: executes a chip wide reset. Executing this command in channel a is equivalent to a hardware reset with the RESETN pin. Executing in channel b-h, has no effect.
1995 May 1
355
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Table 9. Command Register Code
Channel Command Code CR[7:3] 00000 00001 00010 00011 00100 00101 00110 00111 Commands x'12, x13, x'14, x'15, x'1f (marked with*) are global and exist only in channel A's register space. Channel Command NOP Channel Command Code CR[7:3] 10000 10001 10010 10011 10100 10101 10110 10111 Channel Command Description Reserved Description Transmit Xon Transmit Xoff Reset Receiver Gang Write Xon Character Registers * Gang Write Xoff Character Registers * Reset Transmitter Reset Error Status Gang Load Xon Character Registers DC1 * Gang Load Xoff Character Registers DC3 * Xoff Resume Command Host Xoff Command Reserved Reserved Reserved Reserved Reset Break Change Interrupt Begin Transmit Break End Transmit Break 01000 01001 01010 01011 01100 01101 01110 01111 Assert RTSN (I/O2 or I/O1) Set time-out mode on Reserved Set time-out mode off Reserved Reserved 11000 11001 11010 11011 11100 11101 11110 11111 Cancel Transmit X Char command Negate RTSN (I/O2 or I/O1) Reset Address Recognition Status Block Error Status configure Reset All UART channel registers Reset Device *
Table 10. SR - Channel Status Register
Bit 7 Bit 6 Bit 5 Received Break 0 - No 1 - Yes Framing Error 0 - No 1 - Yes Parity Error
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Overrun Error 0 - No 1 - Yes
TxEMT
TxRDY
RxFULL 0 - No 1 - Yes
RxRDY 0 - No 1 - Yes
0 - No 1 - Yes
0 - No 1 - Yes
0 - No 1 - Yes
SR[7] - Received Break This bit indicates that an all zero character of the programmed length has been received without a stop bit. Only a single FIFO position is occupied when a break is received; further entries to the FIFO are inhibited until the RxD line returns to the marking state for at least one half bit time (two successive edges of the internal or external 1x clock). When this bit is set, the change in break bit in the ISR (ISR[2]) is set. ISR[2] is also set when the end of the break condition, as defined above, is detected. The break detect circuitry is capable of detecting breaks that originate in the middle of a received character. However, if a break begins in the middle of a character, it must last until the end of the next character in order for it to be detected. SR[6] - Framing Error (FE) This bit, when set, indicates that a stop bit was not detected when the corresponding data character in the FIFO was received. The stop bit check is made in the middle of the first stop bit position. SR[5] - Parity Error (PE) This bit is set when the 'with parity' or 'force parity' mode is programmed and the corresponding character in the FIFO was received with incorrect parity. In the special 'wake up mode', the parity error bit stores the received A/D bit.
occurs, the character in the receive shift register (and its break detect, parity error and framing error status, if any) is lost. This bit is cleared by a reset error status command. SR[3] - Transmitter Empty (TxEMT) This bit is set when the transmitter underruns, i.e., both the TxFIFO and the transmit shift register are empty.
It is set after transmission of the last stop bit of a character, if no character is in the TxFIFO awaiting transmission. It is reset when the TxFIFO is loaded by the CPU, or when the transmitter is disabled. SR[2] - Transmitter Ready (TxRDY) This bit, when set, indicates that the TxFIFO is ready to be loaded with a character. This bit is cleared when the TxFIFO is loaded by the CPU and is set when the last character is transferred to the transmit shift register. TxRDY is reset when the transmitter is disabled and is set when the transmitter is first enabled, e.g., characters loaded in the TxFIFO while the transmitter is disabled will not be transmitted. SR[1] - RxFIFO Full (RxFULL) This bit is set when a character is transferred from the receive shift register to the receive FIFO and the transfer causes the FIFO to become full, i.e., all sixteen RxFIFO positions are occupied. It is reset when the CPU reads the RxFIFO and that read leaves one empty byte position. If a character is waiting in the receive shift register because the RxFIFO is full, RxFULL is not reset until the second read of the RxFIFO since the waiting character is immediately loaded to the RxFIFO. 356
SR[4] - Overrun Error (OE) This bit, when set, indicates that one or more characters in the received data stream have been lost. It is set upon receipt of a new character when the RxFIFO is full and a character is already in the receive shift register waiting for an empty FIFO position. When this 1995 May 1
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA A A A AAAAA A A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA A A A
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA AA AAAAAAAA A A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AA AA
Table 11. ISR - Interrupt Status Register
Bit 7 Bit 6 Bit 5 I/O Port change of state Receiver Watch-dog Time-out Address recognition event Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Xon/off event Always 0 Change of Break State RxRDY Receiver has entered arbitration process TxRDY Transmitter has entered arbitration process This register provides the status of all potential interrupt sources for a UART channel. When generating an interrupt arbitration value, the contents of this register are masked by the interrupt mask register (IMR). If a bit in the ISR is a '1' and the corresponding bit in the IMR is also a '1', interrupt arbitration for this source will begin. If the corresponding bit in the IMR is a zero, the state of the bit in the ISR can have no affect on the IRQN output. Note that the IMR may or may not mask the reading of the ISR as determined by MR1[6]. If MR1[6] is cleared, the reset and power on default, the ISR is read without modification. If MR1[6] is set, the a read of the ISR gives a value of the ISR ANDed with the IMR. ISR[7] - Input Change of State This bit is set when a change of state occurs at the I/O1 or I/O0 input pins. It is reset when the CPU reads the Input Port Register, IPR. ISR[6] Watch-dog Time-out This bit is set when the receiver's watch-dog timer has counted more than 64 bit times since the last RxFIFO event. RxFIFO events are a read of the RxFIFO or GRxFIFO, or the push of a received character into the FIFO. The interrupt will be cleared automatically upon the push of the next character received or when the RxFIFO or GRxFIFO is read. The receiver watch-dog timer is included to allow detection of the very last characters of a received message that may be waiting in the RxFIFO, but are too few in number to successfully initiate an interrupt. Refer to the watch-dog timer description for details of how the interrupt system works after a watch-dog time-out. ISR[5] - Address Recognition Status Change This bit is set when a change in receiver state has occurred due to an Address character being received from an external source and comparing to the reference address in ARCR. The bit and interrupt is negated by a write to the CR with command x11011, Reset Address Recognition Status. ISR[4] - Xon/Xoff Status Change This bit is set when an Xon/Xoff character being received from an external source. The bit is negated by a read of the channel Xon Interrupt Status Register, XISR. ISR[3] - Reserved Always reads a 0 ISR[2] - Change in Channel Break Status This bit, when set, indicates that the receiver has detected the beginning or the end of a received break. It is reset when the CPU issues a reset break change interrupt command via the CR. ISR[1] - Receiver Ready The general function of this bit is to indicate that the RxFIFO has data available. The particular meaning of this bit is programmed by MR2[3:2]. If programmed as receiver ready(MR2[3:2] = 00), it indicates that at least one character has been received and is waiting in the RxFIFO to be read by the host CPU. It is set when the character is transferred from the receive shift register to the RxFIFO and reset when the CPU reads the last character from the RxFIFO. If MR2[3:2] is programmed as FIFO full, ISR[1] is set when a character is transferred from the receive holding register to the RxFIFO and the transfer causes the RxFIFO to become full, i.e. all sixteen FIFO positions are occupied. It is reset when ever RxFIFO is not full. If there is a character waiting in the receive shift register because the FIFO is full, the bit is set again when the waiting character is transferred into the FIFO. The other two conditions of these bits, 3/4 and half full operate in a similar manner. The ISR[1] bit is set when the RxFIFO fill level meets or exceeds the value; it is reset when the fill level is less. See the description of the MR2 register. Note: This bit must be at a one (1) for the receiver to enter the arbitration process. It is the fact that this bit is zero (0) when the RxFIFO is empty that stops an empty FIFO from entering the interrupt arbitration. Also note that the meaning if this bit is not quite the same as the similar bit in the status register (SR). ISR[0] - Transmitter Ready The general function of this bit is to indicate that the TxFIFO has an at least one empty space for data. The particular meaning of the bit is controlled by MR0[5:4] indicates the TxFIFO may be loaded with one or more characters. If MR0[5:4] = 00 (the default condition) this bit will not set until the TxFIFO is empty - sixteen bytes available. If the fill level of the TxFIFO is below the trigger level programmed by the TxINT field of the Mode Register 0, this bit will be set. A one in this position indicates that at least one character can be sent to the TxFIFO. It is turned off as the TxFIFO is filled above the level programmed by MR0[5:4. This bit turns on as the FIFO empties; the RxFIFO bit turns on as the FIFO fills. This often a point of confusion in programming interrupt functions for the receiver and transmitter FIFOs. Note: This bit must be at a one (1) for the transmitter to enter the arbitration process. It is the fact that this bit is zero (0) when the RxFIFO is full that stops a full FIFO from entering the interrupt arbitration. Also note that the meaning if this bit is not quite the same as the similar bit in the status register (SR).
SR[0] - Receiver Ready (RxRDY) This bit indicates that a character has been received and is waiting in the RxFIFO to be read by the CPU. It is set when the character is
transferred from the receive shift register to the RxFIFO and reset when the CPU reads the RxFIFO, and no more characters are in the RxFIFO.
Table 12. IMR - Interrupt Mask Register
Bit 7 Bit 6 I/O Port change of state Receiver Watch-dog Time-out
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Address recognition event
Xon/off event
Set to 0
Change of Break State
RxRDY interrupt
TxRDY interrupt
The programming of this register selects which bits in the ISR cause an interrupt output. If a bit in the ISR is a '1' and the corresponding bit in the IMR is a '1', the interrupt source is presented to the internal 1995 May 1
interrupt arbitration circuits, eventually resulting in the IRQN output being asserted (low). If the corresponding bit in the IMR is a zero, the state of the bit in the ISR has no affect on the IRQN output.
357
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
IMR[7] - Controls if a change of state in the inputs equipped with input change detectors will cause an interrupt. IMR[6] - Controls the generation of an interrupt by the watch-dog timer event. If set, a count of 64 idle bit times in the receiver will begin interrupt arbitration. IMR[5] - Enables the generation of an interrupt in response to changes in the Address Recognition circuitry of the Special Mode (multi-drop or wake-up mode).
IMR[4] - Enables the generation of an interrupt in response to recognition of an in-band flow control character. IMR[3] - Reserved IMR[2] - Enables the generation of an interrupt when a Break condition has been detected by the channel receiver. IMR[1] - Enables the generation of an interrupt when servicing for the RxFIFO is desired. IMR[0] - Enables the generation of an interrupt when servicing for the TxFIFO is desired.
AAAAAAAAAAAAAAAAA A AAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAA A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAA A A A AAA AAAAAAAAAAAAAAAAA AAA AAAAAAAAAAAAAAAAA AAA AAAAAAAAAAAAAAAAA AAAAAAAAAA AA AAAAAAAAAAAAAAAAA AAA AAAAAAAAAAAAAAAAA AAA
Table 13. RxFIFO Receiver FIFO
Bit[10] Bit[9] Bit[8] Break Received Status Framing Error Status Parity Error Status Bits [7:0] 8 data bits MSBs =0 for 7,6,5 bit data This register provides the 3 MSBs of the Interrupt Arbitration number for a Change of State, COS, interrupt.
Table 17. BCRx - Bidding Control Register - Xon
Bits 7:3 Bits 2:0 Reserved MSB of an Xon/Xoff interrupt bid
The FIFO for the receiver is 11 bits wide and 16 "words" deep. The status of each byte received is stored with that byte and is moved along with the byte as the characters are read from the FIFO. The upper three bits are presented in the STATUS register and they change in the status register each time a data byte is read from the FIFO. Therefor the status register should be read BEFORE the byte is read from the RxFIFO if one wishes to ascertain the quality of the byte The forgoing applies to the "character error" mode of status reporting. See MR1[5] and "RxFIFO Status" descriptions for "block error" status reporting. Briefly "Block Error" gives the accumulated error of all bytes received in the RxFIFO since the last "Reset Error" command was issued. (CR = x'04)
This register provides the 3 MSBs of the Interrupt Arbitration number for an Xon/Xoff interrupt.
Table 18. BCRA - Bidding Control Register - Address
Bits 7:3 Bits 2:0 Reserved
MSB of an address recognition event interrupt bid
This register provides the 3 MSBs of the Interrupt Arbitration number for an address recognition event interrupt.
Table 14. TxFIFO - Transmitter FIFO
Bits 7:0
Table 19. XonCR - Xon Character Register
Bits 7:0 8 Bits of the Xon Character Recognition
8 data bits. MSBs set to 0 for 7, 6, 5 bit data
The FIFO for the transmitter is 8 bits wide by 16 bytes deep. For character lengths less than 8 bits the upper bits will be ignored by the transmitter state machine and thus are effectively discarded.
An 8 bit character register that contains the compare value for an Xon character.
Table 15. BCRBRK - Bidding Control Register - Break Change
Bits 7:3 Bits 2:0 Reserved MSB of break change interrupt bid
Table 20. XoffCR - Xoff Character Register
Bits 7:0 8 Bits of the Xoff Character Recognition
This register provides the 3 MSBs of the Interrupt Arbitration number for a break change interrupt.
An 8 bit character register that contains the compare value for an Xoff character.
Table 16. BCRCOS - Bidding Control Register - Change of State
Bits 7:3 Bits 2:0 Reserved MSB of a COS interrupt bid
Table 21. ARCR - Address Recognition Character Register
Bits 7:0 8 Bits of the Multi-Drop Address Character Recognition
Read as x'0
An 8 bit character register that contains the compare value for the wake-up address character
1995 May 1
358
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAA AAAAAAA AAA A A A A A A A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAA AAA A A A A A A AAAAAAA AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA AAAAAA AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA AAAAAA AAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Table 22. XISR - Xon-Xoff Interrupt Status Register
Bits 7:6 Bits 5:4 Received X Character Status 00 - none 01 - Xoff received 10 - Xon received 11 - both received Automatic X Character transmission status Bits 3:2 Bits 1:0 TxD flow status TxD character status 00 - none 01 - Xon transmitted 10 - Xoff transmitted 11 - Illegal, does not occur 00 - normal 01 - TxD halt pending 10 - re-enabled 11 - flow disabled 00 - normal TxD data 01 - wait on normal data 10 - Xoff in pending 11 - Xon in pending XISR[7:6] - Received X Character Status. This field can be read to determine if the receiver has encountered an Xon or Xoff character in the incoming data stream. These bits are maintained until a read of the XISR. The field is updated by X character reception regardless of the state of MR0(7, 3:2) or IMR(4). The field can therefore be used as a character detector for the bit patterns stored in the Xon and Xoff Character Registers. XISR[5:4] - Automatic transmission Status. This field indicates the last flow control character sent in the Auto Receiver flow control mode. If Auto Receiver mode has not been enabled, this field will always read b'00. It will likewise reset to b'00 if MR0(3) is reset. If the Auto Receiver mode is exited while this field reads b'10, it is the user's responsibility to transmit an Xon, when appropriate.
Table 23. WDTRCR - Watch-dog Timer Enable Register
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 WDT h 1 on 0 off WDT g 1 on 0 off WDT f 1 on 0 off WDT e 1 on 0 off WDT d 1 on 0 off WDT c 1 on 0 off WDT b 1 on 0 off
Bit 0
WDT a 1 on 0 off
This register enables the watch-dog Timer for each of the 8 receivers on the Octal UART.
XISR[3:2] - TxD flow Status. This field tracks the transmitter's flow status as follows: 00 - normal. The flow control is under host control. 01 - TxD halt pending. After the current character finishes the transmitter will stop. The status will then change to b'00. 10 - re-enabled. The transmitter had been halted and restarted. It is sending data characters. After a read of the XISR, it will return to "normal" status. 11 - disabled. The transmitter is flow controlled.
Table 24. BRGTRU - BRG Timer Reload Registers, Upper
Bits 7:0 8 MSB of the BRG Timer divisor.
This is the upper byte of the 16 bit value used by the BRG timer in generating a baud rate clock
Table 25. BRGTRL - BRG Timer Reload Registers, Lower
Bits 7:0 8 LSB of the BRG Timer divisor.
XISR[1:0] - TxD character Status. This field allows determination of the type of character being transmitted. If XISR(1:0) is b'01, the channel is waiting for a data character to transfer from the TxFIFO. This condition will only occur for a bit time after an Xon or Xoff character transmission unless the TxFIFO is empty.
This is the lower byte of the 16 bit value used by the BRG timer in generating a baud rate clock.
Table 26. BRGTCR - BRG Timer Control Register (BRGTCR)
Bit 7 Bit 6:4 BRGTCR b, Register control BRGTCR b, Clock selection
Bit 3
Bit 2:0
BRGTCR a, Register control
BRGTCR a, Clock selection
0 - Resets the timer register and holds it stopped 1 - Allows the timer register to run.
000 - Sclk / 16 001 - Sclk / 32 010 - Sclk/ 64 011 - Sclk / 128 100 - X1 101 - X1 / 2 110 - I/O1b 111 - GIN(1)
0 - Resets the timer register and holds it stopped. 1 - Allows the timer register to run.
000 - Sclk / 16 001 - Sclk / 32 010 - Sclk / 64 011 - Sclk / 128 100 - X1 101 - X1 / 2 110 - I/O1a 111 - GIN(0)
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A
Table 27. ICR - Interrupt Control Register
Bit 7 Reserved. Set to 0 Bits 6:0 Upper seven bits of the Arbitration Threshold This register provides a single 7 bit field called the interrupt threshold for use by the interrupt arbiter. The field is interpreted as a single unsigned integer. The interrupt arbiter will not generate an external interrupt request, by asserting IRQN, unless the value of 1995 May 1 the highest priority interrupt exceeds the value of the interrupt threshold. If the highest bidder in the interrupt arbitration is lower than the threshold level set by the ICR, the Current Interrupt Register, CIR, will contain x'00. Refer to the functional description of 359
Start/Stop control and clock select register for the two BRG counters. The clock selection is for the input to the counters. It is that clock divided by the number represented by the BRGTU and BRGTL the will be used as the 16x clock for the receivers and transmitters. When the BRG timer Clock is selected for the
receiver(s) or transmitter(s) the receivers and transmitters will consider it as a 16x clock and further device it by 16. In other words the receivers and transmitters will always be in the 16x ode of operation when the internal BRG timer is selected for their clock.
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
interrupt generation for details on how the various interrupt source bid values are calculated. Note: While a watch-dog Timer interrupt is pending, the ICR is not used and only receiver codes are presented for interrupt arbitration. This allows receivers with very low count values (perhaps below the threshold value) to win interrupt arbitration without requiring the user to explicitly lower the threshold level in the ICR. These bits are the upper seven (7) bits of the interrupt arbitration system. The lower three (3) bits represent the channel number.
If CIR[7] = 1, then a receiver interrupt is pending and the count is CIR[5:3], channel is CIR[2:0] Else If CIR[6] = 1 then a transmitter interrupt is pending and the count is CIR[5:3], channel is CIR[2:0] Else the interrupt is another type, specified in CIR[5:3] Note: The GIBCR, Global Interrupting Byte Count Register, may be read to determine an exact character count if 9 or less characters are indicated in the count field of the CIR.
AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA A A A AAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAA A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA
UCIR - Update CIR Table 29. IVR - Interrupt Vector Register
Bits 7:0 8 data bits of the Interrupt Vector (IVR) A command based upon a decode of address x'8C. ( UCIR is not a register!) A write (the write data is not important; a "don't care") to this 'register' causes the Current Interrupt Register to be updated with the value that is winning interrupt arbitration. The register would be used in systems that poll the interrupt status registers rather than wait for interrupts. Alternatively, the CIR is normally updated during an Interrupt Acknowledge Bus cycle in interrupt driven systems. The IVR contains the byte that will be placed on the data bus during an IACKN cycle when the GCCR bits (2:1) are set to binary `01'. This is the unmodified form of the interrupt vector.
Table 30. Modification of the IVR
Bits 7:5 Bits 4:3 Always contains bits (7:5) of the IVR Will be replaced with current interrupt type if IVC field of GCCR > 1
Bits 2:0
Table 28. CIR - Current Interrupt Register
Bits 7:6 Bits 5:3 Type Current byte count/type
Bits 2:0
Replaced with interrupting channel number if IVC field of GCCR > 0
Channel number 000 = a 001 = b 010 = c 011 = d
00 - other
000 - no interrupt 001 - Change of State 010 - Address Recognition 011 - Xon/Xoff status 100 - Not used 101 - Break change 110, 111 do not occur Current count code 0 => 9 or less characters 1 => 10 characters . . 5 => 14 characters 6 => 15 characters 7 => 16 (See also GIBCR)
The table above indicates how the IVR may be modified by the interrupting source. The modification of the IVR as it is presented to the data bus during an IACK cycle is controlled by the setting of the bits (2:1) in the GCCR (Global Chip Configuration Register)
111 = h
Table 31. GICR - Global Interrupting Channel Register
Bits 7:3 Bits 2:0 Reserved Channel code
01 - Transmit 11- Receive w/ errors 10 - Receive w/o errors
000 = a 001 = b 010 = c 011 = d
100 = e 101 = f 110 = g 111 = h
000 = a 001 = b 010 = c 011 = d
111 = h
A register associated with the interrupting channel as defined in the CIR. It contains the interrupting channel code for all interrupts.
The Current Interrupt Register is provided to speed up the specification of the interrupting condition in the Octal UART. The CIR is updated at the beginning of an interrupt acknowledge bus cycle or in response to an Update CIR command. (see immediately above) Although interrupt arbitration continues in the background, the current interrupt information remains frozen in the CIR until another IACKN cycle or Update CIR command occurs. The LSBs of the CIR provide part of the addressing for various Global Interrupt registers including the GIBCR, GICR, GITR and the Global RxFIFO and TxFIFO FIFO. The host CPU need not generate individual addresses for this information since the interrupt context will remain stable at the fixed addresses of the Global Interrupt registers until the CIR is updated. For most interrupting sources, the data available in the CIR alone will be sufficient to set up a service routine. The CIR may be processed as follows: 1995 May 1
Table 32. GIBCR - Global Interrupting Byte Count Register
Bits 7:4 Bits 3:0 Reserved Channel byte count code
0000 = 1 AND RxRDY status set for RxFIFO 0000 = 1 AND TxRDY status set for TxD 0001 = 2 0010 = 3 . 1111 = 16
A register associated with the interrupting channel as defined in the CIR. Its numerical value equals the number of bytes minus 1 (count - 1) ready for transfer to the transmitter or transfer from the receiver. It is undefined for other types of interrupts
360
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AA A A A A A A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Table 33. Global Interrupting Type Register
Bit 7:6 Bit 5 Receiver Interrupt Transmitter Interrupt Bit 4:3 Bit 2:0 Reserved read b'00 Other types 0x - not receiver 10 - with receive errors 11 - w/o receive errors 0 - not transmitter 1 - transmitter interrupt 000 - not "other" type 001 - Change of State 010 - Address Recognition Event 011 - Xon/Xoff status 100 - Not used 101 - Break Change 11x - do not occur A register associated with the interrupting channel as defined in the CIR. It contains the type of interrupt code for all interrupts.
Table 35. GTxFIFO - Global TxFIFO Register
Bits 7:0
Table 34. GRxFIFO - Global RxFIFO Register
Bits 7:0
8 data bits of TxFIFO. MSBs not used for 7, 6, 5 bit data
8 data bits of RxFIFO. MSBs set to 0 for 7, 6, 5 bit data
The RxFIFO of the channel indicated in the CIR channel field. Undefined when the CIR interrupt context is not a receiver interrupt. Global TxFIFO Register
The TxFIFO of the channel indicated in the CIR channel field. Undefined when the CIR interrupt context is not a transmitter interrupt. Writing to the GTxFIFO when the current interrupt is not a transmitter event may result in the characters being transmitted on a different channel than intended.
Table 36. IPR - Input Port Register,
Bit 7 Bit 6 I/O3 change I/O2 change
Bit 7
Bit 6
Bit 3
Bit 2
Bit 1
Bit 0
I/O1 change
I/O0 change
I/O3 state
I/O2 state
I/O1 state
I/O0 state
0 - no change 1 - change
0 - no change 1 - change
0 - no change 1 - change
0 - no change 1 - change
The actual logic level at the I/O pin. 1 = high level; 0 =- low level.
This register may be read to determine the current level of the I/O pins and examine the output of the change detectors assigned to
each pin. If the change detection is not enabled or if the pin is configured as an output, the associated change field will read b'0.
Table 37. I/OPIOR - I/O Port Interrupt and Output Register
Bit 7 Bit 6 Bit 5 Bit 4 I/O3 enable 0 - disable 1 - enable I/O2 enable 0 - disable 1 - enable I/O1 enable 0 - disable 1 - enable I/O0 enable 0 - disable 1 - enable
Bit 3
Bit 2
Bit 1
Bit 0
I/O3 output OPR[3]
I/O2 output OPR[2]
I/O1 output OPR[1]
I/O0 output OPR[0]
I/OPIOR[7:4] bits activate the input change of state detectors. If a pin is configured as an output, a b'1 value written to a I/O field has no effect.
I/OPIOR[3:0] bits hold the datum which is the inverse of the datum driven to its associated I/O pin when the I/OPCR control bits for that pin are programmed to b'01.
Table 38. I/OPCR - I/O Port Configuration Register
Bits 7:6 Bits 5:4 I/O3 control I/O2 control
Bits 3:2
Bits 1:0
I/O1 control
I/O0 control
00 - GPI/TxC input 01 - I/OPIOR[3] output 10 - TxC16x output 11 - TxC1x output
00 - GPI/RxC input 01 - I/OPIOR[2]/RTSN * 10 - RxC1x output 11 - RxC16x output
00 - GPI input 01 - I/OPIOR[1]/RTSN * 10 - Reserved 11 - RxC1x output
00 - GPI/CTSN input 01 - I/OPIOR[0]output 10 - TxC1x output 11 - TxC16x output
* If I/OPCR(5:4) is programmed as '01' then the RTSN functionality is assigned to I/O2, otherwise, this function can be implemented on I/O1. (This allows for a lower pin count package option)
power up or reset. Inputs may be used as RxC, TxC inputs or CTSN and General Purpose Inputs simultaneously. All inputs are equipped with change detectors that may be used to generate interrupts or can be polled, as required. NOTE: To ensure that CTSN, RTSN and an external RxC are always available, if I/O2 is not selected as the RTSN output, the RTSN function is automatically provided on I/O1.
This register contains 4, 2 bit fields that set the direction and source for each of the I/O pins associated with the channel. The I/O2 output may be RTSN if MR1[7] is set, or may signal "end of transmission" if MR2[5] is set.(Please see the descriptions of these functions under the MR1 and MR2 register descriptions) If this control bit is cleared, the pin will use the OPR[2] as a source if I/OPCR[5:4] is b'01. The b'00 combinations are always inputs. This register resets to x'0, effectively configuring all I/O pins as inputs on 1995 May 1 361
GENERAL PURPOSE OUTPUT PIN CONTROL
The following four registers control the function of the GOUT0 pin. These output pins have a unique control matrix which includes a
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
clocking mechanism that will allow the pin to change synchronously with an internal or external stimulus. See diagram below.
Table 41. GPOC - General Purpose Output Clk Register
This controls the clock source for GPOR that will clock and/or toggle the data from the selected GPOD source. When code b'00 is selected, no clock will be provided, thereby preventing any change through the D port. Bits 7:6 Bits 5:4 Bits 3:2 Bits 1:0 Clk Sel GPOR(3) Clk Sel GPOR(2) Clk Sel GPOR(1) Clk Sel GPOR(0)
AAAAA A A A A AAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A A AAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAA A AAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAA A A A
GPOSR selects the signal or data source for the GOUT0 pin. The Tx and Rx clock selection is straight forward. The selection of the GPOR allows a more flexible timing control of when the GOUT0 pin changes. Bits 7:4 Bits 3:0 Reserved Global General Purpose Output 0 Selection 0000 - 0111 reserved 1000 = TxC1x a 1001 = TxC16x a 1010 = RxC16x a 1011 = TxC16x b 1100 = GGPOR(3) 1101 = GGPOR(2) 1110 = GGPOR(1) 1111 = GGPOR(0) 00 = none 01 = GIN0 10 = GIN1 11 = reserved 00 = none 01 = GIN0 10 = GIN1 11 = reserved 00 = none 01 = GIN0 10 = GIN1 11 = I/O3c 00 = none 01 = GIN0 10 = GIN1 11 = I/O3a
Table 39. GPOSR - General Purpose Output Select Register
Table 42. GPOD - General Purpose Output Data Register
Table 40. GPOR - General Purpose Output Register
This register selects the data that will be presented to the GPOR "D" input. Note that selection b'10 selects the inverted GPOR data as the input. In this case, the GPOR output will toggle synchronously with the clock selected in the GPOC. Bits 7:6 Bits 5:4 Bits 3:2 Bits 1:0 Data Sel GPOR(3) Data Sel GPOR(2) Data Sel GPOR(1) Data Sel GPOR(0)
This register is a read/write register. Its contents may be altered by a GPOR Write or by the GPOC and GPOD registers shown below. The GPOD and GPOC may be programmed to cause the individual bits of the GPOR to change synchronously with internal or external events. The cells of this register may be thought of as a "Two Port flip-flop"; one port is controlled by a D input and clock, the other by a data load strobe. A read of the GPOR always returns its current value regardless of the port from which it was loaded. Bits 7:4 Bit 3 Bit 2 Bit 1 Bit 0 Reserved GPOR(3) GPOR(2) GPOR(1) GPOR(0)
00 = '1' 01 = '0' 10 = GPOR3N 11 = reserved
00 = '1' 01 = '0' 10 = GPOR2N 11 = reserved
00 = '1' 01 = '0' 10 = GPOR1N 11 = I/O3d
00 = '1' 01 = '0' 10 = GPOR0N 11 = I/O3b
GPOD
GPOR
GPOSR
4:1 MULTIPLEX "1" "0" GPORON 1/O3b
DATA BUS GPOR R/W
DATA IN/OUT DATA READ/WRITE
TxC1Xa TxC16Xa RxC16Xa TxC16Xb
GPO PIN
D INPUT GPOR(0) GPOR(1) GPOR(2) GPOR(3)
QN 4:1 MULTIPLEX D CLOCK NONE GIN0 GIN1 1/O3a
8:1 MULTIPLEX
SD00526
Figure 1. General Purpose Pin Control Logic
1995 May 1
362
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAA AAAAA A A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAA A A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA AA A A AAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AA A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A
The registers of the SC26C198 are partitioned into two groups: those used in controlling data channels and those used in handling the actual data flow and status. Below is shown the general configuration of all the register addressed. The "Register Map Summary" shows the configuration of the lower four bits of the address that is the same for the individual UARTs. It also shows the addresses for the several in the address space of UART A and
Table 43. Summary Register Map, Control
1995 May 1
REGISTER MAP SUMMARY
Philips Semiconductors
REGISTER MAPS
0001 1111 (x1F)
0001 1101 (x1D)
0001 1011 (x1B)
0000 1111 (x0F)
0ccc 1110 (x0E)
0000 1101 (x0D)
0ccc 1100 (x0C)
0ccc 1010 (x0A)
0ccc 1001 (x09)
0ccc 1000 (x08)
0ccc 0111 (x07)
0ccc 0110 (x06)
0ccc 0100 (x04)
0ccc 0011 (x03)
0ccc 0010 (x02)
0ccc 0001 (x01)
0ccc 0000 (x00)
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Address (hex) ccc = channel
Interrupt Vector Register
Watch-dog Timer Run Control
Interrupt Control Register
Global Chip Configuration Register
Transmitter Clock Select Register
Test Register
Receiver Clock Select Register
Address Recognition Character
Xoff Character Register
Xon Character Register
Bid Control, Address recognition
Bid Control, Xon/Xoff
Bid Control, Change of State
Bid Control, Break Change
I/O Port Configuration Reg a I/OPCRa
Mode Register 1 MR1a
Mode Register 0 MR0a
Register Name
363 NOTE: The register maps for channels A and B (UARTs A and B) contain some control registers that configure the entire chip. These are denoted by a symbol. UART B that apply to the total chip configuration. The "Register Map Detail" shows the use of every address in the 8 bit address space. Reserved, set to 0 WDTRCR Acronym BCRCOS BCRBRK RxCSR TxCSR XonCR XoffCR IOPCR GCCR ARCR BCRA BCRX MR1 MR0 ICR
SC26C198 SC68C198 SC26L198 SC68L198
IVR
Read / Write
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Product specification
Page
29 21 24 24 29 29 29 28 28 28 28 32 22 22
AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A
1995 May 1 NOTE: The register maps for channels A and B (UARTs A and B) contain some control registers that configure the entire chip. These are denoted by a symbol
Table 45. Register Map, Control
REGISTER MAP DETAIL
Table 44. Summary Register Map, Data
Philips Semiconductors
0000 1111 (x0F) A(7:0)
0000 1110 (x0E)
0000 1101 (x0D)
0000 1100 (x0C)
0000 1011 (x0B)
0000 1010 (x0A)
0000 1001 (x09)
0000 1000 (x08)
0000 0111 (x07)
0000 0110 (x06)
0000 0101 (x05)
0000 0100 (x04)
0000 0011 (x03)
0000 0010 (x02)
0000 0001 (x01)
0000 0000 (x00)
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Address (hex) ccc = Channel
1001 1101 (x9D)
1001 1101 (x9D)
1001 1100 (x9C)
1000 1100 (x9C)
1001 1101 (x8D)
1000 1100 (x8C)
1000 1100 (x8C)
1001 1011 (x9B)
1000 1011 (x8B)
1000 0100 (x94)
1000 0100 (x84)
1000 1110 (x8E)
1000 1110 (x8E)
1001 0111 (x97)
1000 0111 (x87)
1001 1111 (x9F)
1000 1111 (x8F)
1ccc 0101 (x85)
1ccc 0100 (x84)
1ccc 0010 (x82)
1ccc 0010 (x82)
1ccc 0001 (x81)
1ccc 0001 (x81)
1ccc 0000 (x80)
1ccc 0110 (x86)
1ccc 0011 (x83)
1ccc 0011 (x83)
Receiver Clock Select Register a (RxCSRa)
Address Recognition Character a (ARCRa)
Global Chip Configuration Reg(GCCR) Xmit Clock Select Register a TxCSRa) I/O Port Configuration Reg a I/OPCRa Global Interrupt Type Register Global Interrupt Byte Count BRG Timer Reg Lower b Global Interrupt Channel Reg BRG Timer Control Reg GP Out Data Reg GP Output Reg BRG Timer Reg Lower a Global Chip Configuration Reg Global Transmit FIFO Reg Global Receive FIFO Reg BRG Timer Reg Upper b Current Interrupt Reg Update Current Interrupt Reg GP Out Clk Reg GP Out Select Reg Xon/Xoff Interrupt Status Reg I/O Port Interrupt and Output BRG Timer Reg Upper a Input Port Reg Receiver FIFO Reg Transmitter FIFO Register Interrupt Mask Register Interrupt Status Register Command Register Status Register Mode Register 2 Xon Character Reg a (XonCRa) Xoff Character Reg a (XoffCRa) Mode Register 1 MR1a Mode Register 0 MR0a Test Register BCRCOSa BCRBRKa Reserved Reserved BCRAa BCRXa Read Register Name
364
UART A
Receiver Clock Select Register a (RxCSRa)
Address Recognition Character a (ARCRa)
Global Chip Configuration Reg GCCR) Xmit Clock Select Register a TxCSRa) I/O Port Configuration Reg a I/OPCRa Xon Character Reg a (XonCRa) Xoff Character Reg a (XoffCRa) BRGTRUb BRGTRUa BRGTRLb BGRTRLa Acronym GRxFIFO BRGTCR GTxFIFO I/OPIOR GPOSR RxFIFO TxFIFO GIBCR GPOD GPOR GCCR GPOC GICR UCIR GITR XISR MR2 Mode Register 1 MR1a Mode Register 0 MR0a IMR CIR IPR ISR CR SR Test Register BCRCOSa BCRBRKa Reserved Reserved Write BCRAa BCRXa Read/Write R/W R/W R/W R/W R/W R/W R/W W W W W W W W W W W R R R R R R R R R R
SC26C198 SC68C198 SC26L198 SC68L198
Product specification
Page
32 32 29 31 30 33 33 29 21 32 32 29 30 30 33 33 29 32 29 32 28 28 27 27 25 26 23
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AA A A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Philips Semiconductors 0001 1111 (x1F) 0001 1110 (x1E) 0001 1101 (x1D) 0001 1100 (x1C) 0001 1011 (x1B) 0001 1010 (x1A) 0001 1001 (x19) 0001 1000 (x18) 0001 0111 (x17) 0001 0110 (x16) 0001 0101 (x15) 0001 0100 (x14) 0001 0011 (x13) 0001 0010 (x12) 0001 0001 (x11) 0001 0000 (x10)
1995 May 1 0010 1010 (x2A) 0010 1101 (x2D) 0010 1100 (x2C) 0010 1011 (x2B) 0010 1001 (x29) 0010 1000 (x28) 0010 0101 (x25) 0010 0100 (x24) 0010 0010 (x22) 0010 0001 (x21) 0010 0000 (x20) 0010 1110 (x2E) 0010 0110 (x26) 0010 0011 (x23) 0010 0111 (x27) 0010 1111 (x2F) A(7:0) A(7:0) Mode Register 1 MR1b Mode Register 0 MR0b Mode Register 0 MR0c Mode Register 1 BCRCOSb BCRCOSc BCRBRKb BCRBRKc Reserved Reserved Reserved Reserved Reserved BCRAb BCRXb BCRAc BCRXc Read Read
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Watch-dog Timer Run Control (WDTRCR)
Receiver Clock Select Register b (RxCSRb)
Receiver Clock Select Register c (RxCSRc)
Address Recognition Character b (ARCRb)
Address Recognition Character c (ARCRc)
Xmit Clock Select Register b (TxCSRb)
Xmit Clock Select Register c (TxCSRc)
I/O Port Configuration Reg b I/OPCRb
I/O Port Configuration Reg c I/OPCRc
Interrupt Control Register (ICR)
Interrupt Vector Register (IVR)
Xon Character Reg b (XonCRb)
Xoff Character Reg b (XoffCRb)
Xon Character Reg c (XonCRc)
Xoff Character Reg c (XoffCRc)
365 UART C UART B Receiver Clock Select Register b (RxCSRb) Receiver Clock Select Register c (RxCSRc) Address Recognition Character b (ARCRb) Address Recognition Character c (ARCRc) Watch-dog Timer Run Control (WDTRCR) Xmit Clock Select Register b (TxCSRb) Xmit Clock Select Register c (TxCSRc) I/O Port Configuration Reg b I/OPCRb I/O Port Configuration Reg c I/OPCRc Xon Character Reg b (XonCRb) Xoff Character Reg b (XoffCRb) Xon Character Reg c (XonCRc) Xoff Character Reg c (XoffCRc) Interrupt Control Register (ICR) Interrupt Vector Register (IVR) Mode Register 1 MR1b Mode Register 0 MR0b Mode Register 1 MR1c Mode Register 0 MR0c BCRCOSb BCRCOSc BCRBRKb BCRBRKc Reserved Reserved Reserved Reserved BCRAb BCRXb BCRAc BCRXc Write Write
SC26C198 SC68C198 SC26L198 SC68L198
Reserved
Product specification
A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Philips Semiconductors 01001111 (x4F) 01001110 (x4E) 01001101 (x4D) 01001100 (x4C) 01001011 (x4B) 01001010 (x4A) 01001001 (x49) 01001000 (x48) 01000111 (x47) 01000110 (x46) 01000101 (x45) 01000100 (x44) 01000011 (x43) 01000010 (x42) 01000001 (x41) 01000000 (x40)
1995 May 1 0011 1010 (x3A) 0011 1101 (x3D) 0011 1100 (x3C) 0011 1011 (x3B) 0011 1001 (x39) 0011 1000 (x38) 0011 0101 (x35) 0011 0100 (x34) 0011 0010 (x32) 0011 0001 (x31) 0011 0000 (x30) 0011 1110 (x3E) 0011 0110 (x36) 0011 0011 (x33) 0011 0111 (x37) 0011 1111 (x3F) A(7:0) A(7:0) Mode Register 1 MR1e Mode Register 0 MR0e Mode Register 1 MR1d Mode Register 0 MR0d BCRCOSe BCRCOSd BCRBRKe BCRBRKd Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved BCRAe BCRXe BCRAd BCRXd Read Read
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Receiver Clock Select Register e (RxCSRe)
Receiver Clock Select Register d (RxCSRd)
Address Recognition Character d (ARCRd)
Xmit Clock Select Register e (TxCSRe)
Xmit Clock Select Register d (TxCSRd)
I/O Port Configuration Reg d I/OPCRd
Address Recognition Char e (ARCRe)
I/OPort Configuration Reg e I/OPCRe
Xon Character Reg e (XonCRe)
Xon Character Reg d (XonCRd)
Xoff Character Reg e (XoffCRe)
Xoff Character Reg d (XoffCRd)
366 UART D UART E Receiver Clock Select Register e (RxCSRe) Receiver Clock Select Register d (RxCSRd) Address Recognition Character d (ARCRd) Xmit Clock Select Register e (TxCSRe) Xmit Clock Select Register d (TxCSRd) I/O Port Configuration Reg d I/OPCRd Address Recognition Char e (ARCRe) I/OPort Configuration Reg e I/OPCRe Xon Character Reg e (XonCRe) Xon Character Reg d (XonCRd) Xoff Character Reg e (XoffCRe) Xoff Character Reg d (XoffCRd) Mode Register 1 MR1e Mode Register 0 MR0e Mode Register 1 MR1d Mode Register 0 MR0d BCRCOSe BCRCOSd BCRBRKe BCRBRKd Reserved Reserved Reserved Reserved Reserved Reserved Reserved BCRAe BCRXe BCRAd BCRXd Write Write
SC26C198 SC68C198 SC26L198 SC68L198
Reserved
Product specification
A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Philips Semiconductors 01101111 (x6F) 01101110 (x6E) 01101101 (x6D) 01101100 (x6C) 01101011 (x6B) 01101010 (x6A) 01101001 (x69) 01101000 (x68) 01100111 (x67) 01100110 (x66) 01100101 (x65) 01100100 (x64) 01100011 (x63) 01100010 (x62) 01100001 (x61) 01100000 (x60) 01011111 (x5F) 01011110 (x5E) 01011101 (x5D) 01011100 (x5C) 01011011 (x5B) 01011010 (x5A) 01011001 (x59) 01011000 (x58) 01010111 (x57) 01010110 (x56) 01010101 (x55) 01010100 (x54) 01010011 (x53) 01010010 (x52) 01010001 (x51) 01010000 (x50)
1995 May 1 A(7:0) Mode Register 1 MR1g Mode Register 0 MR0g Mode Register 1 MR1f Mode Register 0 MR0f BCRCOSg BCRBRKg BCRCOSf BCRBRKf Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved BCRAg BCRXg BCRAf BCRXf Read
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Receiver Clock Select Register g (RxCSRg)
Receiver Clock Select Register f (RxCSRf)
Xmit Clock Select Register g (TxCSRg)
Xmit Clock Select Register f (TxCSRf)
Address Recognition Char g (ARCRg)
I/OPort Configuration Reg g I/OPCRg
Address Recognition Char f (ARCRf)
I/OPort Configuration Reg f I/OPCRf
Xon Character Reg g (XonCRg)
Xoff Character Reg g (XoffCRg)
Xon Character Reg f (XonCRf)
Xoff Character Reg f (XoffCRf)
367 UART G UART F Receiver Clock Select Register g (RxCSRg) Receiver Clock Select Register f (RxCSRf) Xmit Clock Select Register g (TxCSRg) Xmit Clock Select Register f (TxCSRf) Address Recognition Char g (ARCRg) I/OPort Configuration Reg g I/OPCRg Address Recognition Char f (ARCRf) I/OPort Configuration Reg f I/OPCRf Xon Character Reg g (XonCRg) Xoff Character Reg g (XoffCRg) Xon Character Reg f (XonCRf) Xoff Character Reg f (XoffCRf) Mode Register 1 MR1g Mode Register 0 MR0g Mode Register 1 MR1f Mode Register 0 MR0f BCRCOSg BCRBRKg BCRCOSf BCRBRKf Reserved Reserved Reserved Reserved Reserved Reserved Reserved BCRAg BCRXg BCRAf BCRXf Write
SC26C198 SC68C198 SC26L198 SC68L198
Reserved
Product specification
AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Philips Semiconductors 01111111 (x7F) 01111110 (x7E) 01111101 (x7D) 01111100 (x7C) 01111011 (x7B) 01111010 (x7A) 01111001 (x79) 01111000 (x78) 01110111 (x77) 01110110 (x76) 01110101 (x75) 01110100 (x74) 01110011 (x73) 01110010 (x72) 01110001 (x71) 01110000 (x70)
1995 May 1 Mode Register 1 MR1h Mode Register 0 MR0h BCRCOSh BCRBRKh Reserved Reserved Reserved Reserved BCRAh BCRXh
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Receiver Clock Select Register h (RxCSRh)
Xmit Clock Select Register h (TxCSRh)
Address Recognition Char h (ARCRh)
I/OPort Configuration Reg h I/OPCRh
Xon Character Reg h (XonCRh)
Xoff Character Reg h (XoffCRh)
368 UART H Receiver Clock Select Register h (RxCSRh) Xmit Clock Select Register h (TxCSRh) Address Recognition Char h (ARCRh) I/OPort Configuration Reg h I/OPCRh Xon Character Reg h (XonCRh) Xoff Character Reg h (XoffCRh) Mode Register 1 MR1h Mode Register 0 MR0h BCRCOSh BCRBRKh Reserved Reserved Reserved BCRAh BCRXh
SC26C198 SC68C198 SC26L198 SC68L198
Reserved
Product specification
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA AAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A
Table 46. Register Map, Data
Philips Semiconductors
1995 May 1 1001 1010 (x9A) 1001 1101 (x9D) 1001 1101 (x9D) 1001 1100 (x9C) 1001 1100 (x9C) 1000 1101 (x8D) 1000 1100 (x8C) 1001 1011 (x9B) 1000 1011 (x8B) 1001 0101 (x95) 1001 0100 (x94) 1001 0100 (x94) 1001 0010 (x92) 1001 0001 (x91) 1001 0000 (x90) 1000 0101 (x85) 1000 0100 (x84) 1000 0100 (x84) 1000 0010 (x82) 1000 0001 (x81) 1000 0000 (x80) 1001 1110 (x9E) 1000 1110 (x8E) 1001 0110 (x96) 1001 0011 (x93) 1000 0110 (x86) 1000 0011 (x83) 1001 0111 (x97) 1000 0111 (x87) 1001 1111 (x9F) 1000 1111 (x8F) A(7:0) A(7:0) Current Interrupt Reg (CIR) GP Out Data Reg (GPOD) GP Out Clk Reg (GPOC) GP Output Reg (GPOR) Mode Register b (MR2b) Mode Register a (MR2a) Status Register b (SRb) Status Register a (SRa) Input Port Reg b (IPRb) Input Port Reg a (IPRa) Reserved Reserved Reserved Reserved Reserved Reserved Reserved Read Read
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
I/O Port Interrupt and Output b (I/OPIORb)
Global Chip Configuration Reg (GCCR)
I/O Port Interrupt and Output a I/OPIORa)
Xon/Xoff Interrupt Status Reg b (XISRb)
Xon/Xoff Interrupt Status Reg a (XISRa)
Global Receive FIFO Reg (GRxFIFO)
Global Interrupt Type Register (GITR)
Global Interrupt Channel Reg (GICR)
Global Interrupt Byte Count (GIBCR)
Interrupt Status Register b (ISRb)
Interrupt Status Register a (ISRa)
Receiver FIFO Reg b (RxFIFOb)
Receiver FIFO Reg a (RxFIFOa)
GP Out Select Reg (GPOSR)
369 UART B UART A I/O Port Interrupt and Output b (I/OPIORb) I/O Port Interrupt and Output a (I/OPIORa) Global Chip Configuration Reg (GCCR) Global Transmit FIFO Reg (GTxFIFO) BRG Timer Reg Upper b (BRGTRUb) BRG Timer Reg Upper a (BRGTRUa) BRG Timer Control Reg (BRGCTCR) BRG Timer Reg Lower b (BRGTRLb) BRG Timer Reg Lower a (BRGTRLa) Transmitter FIFO Reg b (TxFIFOb) Transmitter FIFO Reg a (TxFIFOa) Interrupt Mask Register b (IMRb) Interrupt Mask Register a (IMRa) GP Out Select Reg (GPOSR) GP Out Data Reg (GPOD) Command Register b (CRb) Command Register a (CRa) GP Output Reg (GPOR)
SC26C198 SC68C198 SC26L198 SC68L198
Mode Register b (MR2b)
Mode Register a (MR2a)
GP Out Clk Reg (GPOC)
Update CIR
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Write Write
Product specification
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AA A A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAA AAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Philips Semiconductors
1995 May 1 1010 1010 (xAA) 1010 1101 (xAD) 1010 1100 (xAC) 1011 1010 (xBA) 1011 1000 (xBB) 1010 1011 (xAB) 1011 1101 (xBD) 1011 1100 (xBC) 1010 1001 (xA9) 1010 1000 (xA8) 1010 0101 (xA5) 1010 0100 (xA4) 1010 0010 (xA2) 1010 0001 (xA1) 1010 0000 (xA0) 1011 1011 (xBB) 1010 1110 (xAE) 1011 1001 (xB9) 1011 0101 (xB5) 1011 0100 (xB4) 1011 0010 (xB2) 1011 0001 (xB1) 1011 0000 (xB0) 1010 0110 (xA6) 1010 0011 (xA3) 1011 1110 (xBE) 1011 0110 (xB6) 1011 0011 (xB3) 1010 0111 (xA7) 1010 1111 (xAF) 1011 0111 (xB7) 1011 1111 (xBF) A(7:0) A(7:0) Mode Register d (MR2d) Mode Register c (MR2c) Status Register d (SRd) Status Register c (SRc) Input Port Reg d (IPRd) Input Port Reg c (IPRc) Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Read Read
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
I/O Port Interrupt and Output d (I/OPIORd)
I/O Port Interrupt and Output c (I/OPIORc)
Xon/Xoff Interrupt Status Reg d (XISRd)
Xon/Xoff Interrupt Status Reg c (XISRc)
Interrupt Status Register d (ISRd)
Interrupt Status Register c (ISRc)
Receiver FIFO Reg d (RxFIFOd)
Receiver FIFO Reg c (RxFIFOc)
370 UART D UART C I/O Port Interrupt and Output d (I/OPIORd) I/O Port Interrupt and Output c (I/OPIORc) Transmitter FIFO Reg d (TxFIFOd) Transmitter FIFO Reg c (TxFIFOc) Interrupt Mask Register d (IMRd) Interrupt Mask Register c (IMRc) Command Register d (CRd) Command Register c (CRc) Mode Register d (MR2d) Mode Register c (MR2c)
SC26C198 SC68C198 SC26L198 SC68L198
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Write Write
Product specification
A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Philips Semiconductors 11011111 (xDF) 11011110 (xDE) 11011101 (xDD) 11011100 (xDC) 11011011 (xDB) 11011010 (xDA) 11011001 (xD9) 11011000 (xD8) 11010111 (xD7) 11010110 (xD6) 11010101 (xD5) 11010100 (xD4) 11010011 (xD3) 11010010 (xD2) 11010001 (xD1) 11010000 (xD0) 11001111 (xCF) 11001110 (xCE) 11001101 (xCD) 11001100 (xCC) 11001011 (xCB) 11001010 (xCA) 11001001 (xC9) 11001000 (xC8) 11000111 (xC7) 11000110 (xC6) 11000101 (xC5) 11000100 (xC4) 11000011 (xC3) 11000010 (xC2) 11000001 (xC1) 11000000 (xC0)
1995 May 1 A(7:0) Mode Register e (MR2e) Status Register e (SRe) Input Port Reg e (IPRe) Mode Register f (MR2f) Status Register f (SRf) Input Port Reg f (IPRf) Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Read
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
I/O Port Interrupt and Output e (I/OPIORe)
I/O Port Interrupt and Output f (I/OPIORf)
Xon/XoffInterrupt Status Reg e (XISRe)
Xon/XoffInterrupt Status Reg f (XISRf)
Interrupt Status Register e (ISRe)
Receiver FIFO Reg e (RxFIFOe)
Interrupt Status Register f (ISRf)
Receiver FIFO Reg f (RxFIFOf)
371 UART E UART F I/O Port Interrupt and Output e (I/OPIORe) I/O Port Interrupt and Output f (I/OPIORf) Transmitter FIFO Reg e (TxFIFOe) Transmitter FIFO Reg f (TxFIFOf) Interrupt Mask Register e (IMRe) Interrupt Mask Register f (IMRf) Command Register e (CRe) Command Register f (CRf)
SC26C198 SC68C198 SC26L198 SC68L198
Mode Register e (MR2e)
Mode Register f (MR2f)
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Write
Product specification
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
RESET CONDITIONS
Philips Semiconductors 11111111 (xFF) 11111110 (xFE) 11111101 (xFD) 11111100 (xFC) 11111011 (xFB) 11111010 (xFA) 11111001 (xF9) 11111000 (xF8) 11110111 (xF7) 11110110 (xF6) 11110101 (xF5) 11110100 (xF4) 11110011 (xF3) 11110010 (xF2) 11110001 (xF1) 11110000 (xF0) 11101111 (xEF) 11101110 (xEE) 11101101 (xED) 11101100 (xEC) 11101011 (xEB) 11101010 (xEA) 11101001 (xE9) 11101000 (xE8) 11100111 (xE7) 11100110 (xE6) 11100101 (xE5) 11100100 (xE4) 11100011 (xE3) 11100010 (xE2) 11100001 (xE1) 11100000 (xE0)
1995 May 1
Cleared registers:
Device Configuration after Hardware Reset or CRa cmd=x1F
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Channel Status Registers (SR) Channel Interrupt Status Registers (ISR) Channel Interrupt Mask Registers (IMR) Channel Interrupt Xon Status Register (XISR) Interrupt Control Register (ICR) Global Configuration Control Register (GCCR) Hence the device enters the asynchronous bus cycling mode. Current Interrupt Register (CIR) BRG Timer Run Control Register (BRGTCR) Watch-dog Timer Run Control Register (WDTRCR) Channel Input/Output Port Configuration Registers (I/OPCR) Hence all I/O pins have direction = Input after reset A(7:0) Xon/XoffInterrupt Status Reg h (XISRh) Xon/XoffInterrupt Status Reg g (XISRg) Interrupt Status Register h (ISRh) Interrupt Status Register g (ISRg) Receiver FIFO Reg h (RxFIFOh) Receiver FIFO Reg g (RxFIFOg) Mode Register h (MR2h) Mode Register g (MR2g) Status Register h (SRh) Status Register g (SRg) Input Port Reg h (IPRh) Input Port Reg g (IPRg) Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Read
I/O Port Interrupt and Output h (I/OPIORh)
I/O Port Interrupt and Output g (I/OPIORg)
372
Halts: Disables: Clears Modes for:
BRG Counter/Timer Registers Transmitters Receivers Interrupts, current and future Power down Test modes Input Port Changed bits Gang write to Xon or Xoff Xon/Xoff/Address detection Receiver error status UART G UART H I/O Port Interrupt and Output h (I/OPIORh) I/O Port Interrupt and Output g (I/OPIORg) Transmitter FIFO Reg h (TxFIFOh) Transmitter FIFO Reg g (TxFIFOg) Interrupt Mask Register h (IMRh) Interrupt Mask Register g (IMRg) Command Register h (CRh) Command Register g (CRg)
BRG Counters Bus cycle in progress (hardware RESET only)
SC26C198 SC68C198 SC26L198 SC68L198
Mode Register h (MR2h)
Mode Register g (MR2g)
Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Write
Product specification
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A
VCC = 5.0V 10%, 0 to 70C
1995 May 1
DC ELECTRICAL SPECIFICATIONS (26C198 and 68C198)
Limitations:
Philips Semiconductors
SYMBOL
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
Minimum RESETN pin pulse width is 10 SClk cycles after Vcc reaches operational range
IODL IODH
IIKX1 IIHX1
IOZH IOZL
VOL VOH
VOL
VIH
ICC
VIL
VIH
IIL IIH
II
Power supply current Operating mode Power down mode (no clocks operating)
Open-drain output low current in off state Open drain output high current in off state
Output off current high, 3-state data bus Output off current low, 3-state data bus
X1/CLK input low current X1/CLK input high current
Input leakage current
Input current low, I/O pins Input current high, I/O pins
Open drain low voltage
Output low voltage (except OD outputs) Output high voltage (except OD outputs)
Input high voltage (X1/CLK)
Input high voltage (except X1/CLK)
Input low voltage
PARAMETER
TEST CONDITIONS
VIN=GND,X2=Open VIN=VCC, X2=Open
TTL Input levels CMOS input levels CMOS input levels
VIN = 0 to VCC
IOL = 14.0mA
IOL = 7.0mA IOH = -400A IOH = -100A
VIN = 0 VIN = VCC
VIN = VCC VIN = VCC
VIN = VCC VIN = 0
373 The user must allow a minimum of 6 SClk cycles to elapse after a reset (RESETN pin or CRa initiated) of the device terminates before initiating a new bus cycle. 0.8 VCC 0.8VCC 0.9VCC -100 MIN VSS -10 -10 -10 2.0 -5
SC26C198 SC68C198 SC26L198 SC68L198
LIMITS
TYP
+100
MAX
VCC
VCC
200 75 25 0.4 0.4 0.8 10 10 10 5
Product specification
UNIT
mA mA A A A A A A V V V V V
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A AA A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA A A AAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A AAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A A AAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AA AAAA A A A AA A A AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA A A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A AAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AA A A A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA
1995 May 1 SYMBOL T/RFsclk TsSTRT Tsclkh Tsclkl Fsclk tRWD tRWH tRWS RXH tRXS tRES tTCS tTXD tSTP tDD tDH tDD tCH fRX tRX tPD tPH tDS tCS tAH tRF tPS tDF tAS fTX tTX tIR
AC ELECTRICAL CHARACTERISTICS5 (26C198 and 68C198)
Philips Semiconductors
Sclk TIMING3
RECEIVER TIMING
TRANSMITTER TIMING
Tx / Rx CLOCK TIMING, External2
INTERRUPT TIMING
I/O PORT PIN TIMING
BUS TIMING
RESET TIMING
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
FIGURE
Sclk rise/fall time (0.8 to 2.0Volts)
Sclk frequency
Min high time at Vih (2.0V)
Min low time at Vil (0.8V)
RxD data setup time to RxC high (Start Bit)
RxD data hold time from RxC high (data)
RxD data setup time to RxC high (data)
TxC output delay from TxD output data
TxD output delay from TxC low
Tx / Rx clock rise and fall times
TxC frequency (16 X) (1 X)
TxC high or low time
RxC frequency (16 X) (1 X)
RxC high or low time
Interrupt vector valid after C3 falling edge, IACKN cycle
IRQN from: Internal interrupt source active bid Software reset to IRQN inactive Write IMR (clear IMR bit after C4 end)
I/O output valid from: Write Sclk C4 rising edge (write to I/OPIOR)
I/O input hold time after Sclk C4 rising edge (Read IPR)
I/O input setup time before Sclk C3 falling edge (Read IPR)
High time between CEN low (ASYNC)
Write cycle data hold time after Sclk C4 rising edge
Write cycle data setup time before Sclk C4 rising edge
Read cycle data bus floating after C4 end (SYNC)
Read cycle data bus floating after CEN high (ASYNC)
Read cycle Data valid after Sclk C3 falling edge
W-Rn hold time after Sclk C3 rising edge
W-Rn setup time before Sclk C2 rising edge
CEN high after C4 end. To terminate cycle (SYNC)
CEN hold time after Sclk C4 high (ASYNC)1
CEN hold time after Sclk C3 high (SYNC)
CEN setup time before Sclk C2 high (SYNC)
CEN setup time before Sclk C1 high (ASYNC)
A0-A7 hold time after Sclk C3 rising edge
A0-A7 setup time before Sclk C3 rising edge
RESET pulse width
PARAMETER
374
17 / 32
MIN
-20
30
30
20
20
22
18
20
12
30
25
20
25
15
18
10
10
11 11 0 0 0 0 5 5 5
SC26C198 SC68C198 SC26L198 SC68L198
1.5 Sclk
1.5 Sclk
1.5 Sclk
LIMITS
TYP
25
10
18
15
20
20
25
12
3
3
MAX
3/3 100 33 20 20 16 1 16 1 37 50 43 50 35 35 37 18
Product specification
16X clk
UNIT
MHz MHz MHz Sclk Sclk ns Sclk Sclk ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
ns
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA A A AAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A A AAA AA A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AA A A A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA
AC ELECTRICAL CHARACTERISTICS (26C198 and 68C198) (Continued)
Philips Semiconductors Gout TIMING I/O PORT External Clock DACKN TIMING4 COUNTER / TIMER BAUD RATE CLOCK (EXTERNAL CLOCK INPUT) X1 / X2 COMMUNICATION CRYSTAL CLOCK2 SYMBOL DAKdlya DAKdlys GPOtdd X1 L / H TC/TLH
NOTES: 1. The ASYNC pulse width low must include 4 rising edges plus the setup & hold times. For those applications where the control processor has no knowledge of the Sclk period, this will imply a CEN period of 5 Sclk rising edges. 2. Production test will use rise and fall time less than 7ns. Specified rise and fall times are guaranteed by design. 3. Sclk is required for proper bus timing. Sclk must always be faster than twice the fastest 1X data clock. 4. The meaning of DACKN is that data will be valid before the end of the C4 time. 5. All voltage measurements are relative to gnd. Input and output levels are those shown in "DC Electrical Specifications". For testing, inputs switch between 0.2 and 2.8V; outputs are measured between 0.8 and 2.0V.
1995 May 1 DAKdly T/RFx1 Tgpirtx TC/TO FC/T Fx1 FIGURE GPO valid after write to GPOR I/OP falling edge to TxD out 1X mode RxD setup to I/OP rising edge 1X mode GPI to Rx/Tx clock out DACK high from CEN high (ASYNC) DACK low from Sclk C4 rising edge Delay C/T clock external to output pin C/T high and low time Clock frequency X1 Rise / Fall time X1 Low / High time X1 clock frequency PARAMETER
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
DACK high from C4 end rising edge (SYNC)
375 MIN 30 20 0 0
SC26C198 SC68C198 SC26L198 SC68L198
LIMITS
3.6864
TBD TBD TBD TBD TYP 28 28
10/10
MAX
8.0
40
40
25
60
8
Product specification
UNIT
MHz
MHz
ns ns ns ns ns ns ns ns ns ns ns
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A AAAAAAAAAAAAAAAAAAAAAAAA A A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A
VCC = 3.3 V 10%, 0 to 70C
1995 May 1 Philips Semiconductors SYMBOL IODL IODH IIKX1 IIHX1 IOZH IOZL VOL VOH VOL VIH ICC VIL
VIH
DC ELECTRICAL SPECIFICATIONS (26L198 and 68L198)
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
IIL IIH
II
Power supply current Operating mode Power down mode (no clocks operating)
Open-drain output low current in off state Open drain output high current in off state
Output off current high, 3-state data bus Output off current low, 3-state data bus
X1/CLK input low current X1/CLK input high current
Input leakage current
Input current low, I/O pins Input current high, I/O pins
Open drain low voltage
Output low voltage (except OD outputs) Output high voltage (except OD outputs)
Input high voltage (X1/CLK)
Input high voltage (except X1/CLK)
Input low voltage
PARAMETER
TEST CONDITIONS
VIN=GND,X2=Open VIN=VCC, X2=Open
TTL Input levels CMOS input levels CMOS input levels
VIN = 0 to VCC
IOL = 10.0mA
IOL = 5.0mA IOH = -400A IOH = -100A
VIN = 0 VIN = VCC
VIN = VCC VIN = VCC
VIN = VCC VIN = 0
376 0.8 VCC 0.8VCC 0.9VCC MIN VSS -50 2.0 -5 -5 -5 -5
SC26C198 SC68C198 SC26L198 SC68L198
LIMITS
TYP
22 12 1
MAX
VCC
VCC
+50
0.4
0.4
0.7
35 20 30 5 5 5 5
Product specification
UNIT
mA mA A A A A A A V V V V V
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA A A AAA A AAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A A AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AA AAAA A A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA A A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A AAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAA AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AA A A A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA
AC ELECTRICAL CHARACTERISTICS5 (26L198 and 68L198)
Philips Semiconductors Sclk RECEIVER TIMING TRANSMITTER TIMING Tx / Rx CLOCK TIMING, INTERRUPT TIMING I/O PORT PIN TIMING BUS TIMING RESET TIMING SYMBOL T/RFsclk TsSTRT
1995 May 1 Tsclkh Tsclkl Fsclk tRWD tRWH tRWS RXH tRXS tRES tTCS tTXD fRX fTX6 tDD tDH tDD tCH tRX tPD tPH tDS tCS tAH tRF tPS tDF tAS tTX tIR TIMING3
6
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
FIGURE
Sclk rise/fall time (0.8 to 2.0Volts)
Sclk frequency
Min high time at Vih (2.0V)
Min low time at Vil (0.8V)
RxD data setup time to RxC high (Start Bit)
RxD data hold time from RxC high (data)
RxD data setup time to RxC high (data)
TxC output delay from TxD output data
TxD output delay from TxC low
Tx / Rx clock rise and fall times
TxC frequency
TxC high or low time
RxC frequency
RxC high or low time
Interrupt vector valid after C3 falling edge, IACKN cycle
IRQN from: Internal interrupt source active bid Software reset to IRQN inactive Write IMR (clear IMR bit after C4 end)
I/O output valid from: Write Sclk C4 rising edge (write to I/OPIOR)
I/O input hold time after Sclk C4 rising edge (Read IPR)
I/O input setup time before Sclk C3 falling edge (Read IPR)
High time between CEN low (ASYNC)
Write cycle data hold time after Sclk C4 rising edge
Write cycle data setup time before Sclk C4 rising edge
Read cycle data bus floating after C4 end (SYNC)
Read cycle data bus floating after CEN high (ASYNC)
Read cycle Data valid after Sclk C3 falling edge
W-Rn hold time after Sclk C3 rising edge
W-Rn setup time before Sclk C2 rising edge
CEN hold time after Sclk C4 high (ASYNC)1
CEN hold time after Sclk C3 high (SYNC)
CEN setup time before Sclk C2 high (SYNC)
CEN setup time before Sclk C1 high (ASYNC)
A0-A7 hold time after Sclk C3 rising edge
A0-A7 setup time before Sclk C3 rising edge
RESET pulse width
External2
PARAMETER
377 (16 X) (1 X) (16 X) (1 X) MIN -20 0.1 20 20 35 35 25 25 22 18 20 15 35 30 35 50 35 40 25 10 0 0 0 0 7 7 7 17 32
SC26C198 SC68C198 SC26L198 SC68L198
1.5 Sclk
1.5 Sclk
1.5 Sclk
LIMITS
.5 Sclk
TYP
34
33
21
13
19
26
34
12
3
MAX
5/5 43 120 75 100 17 20 20 50 80 35 35 50 8 1 8 1
Product specification
16X clk
UNIT
MHz MHz MHz Sclk Sclk ns Sclk ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
ns
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA A A A AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A A AA A A AA A A AAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA AA AA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A A AAA AA A A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AA A A AA A AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAA AA A A A A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA
AC ELECTRICAL CHARACTERISTICS (Continued)
Philips Semiconductors GOUT TIMING I/O PORT External Clock DACKN TIMING4 COUNTER / TIMER BAUD RATE CLOCK (EXTERNAL CLOCK INPUT) X1 / X2 COMMUNICATION CRYSTAL CLOCK2 SYMBOL DAKdlya DAKdlys GPOtdd X1 L / H TC/TLH
NOTES: 1. The ASYNC pulse width low must include 4 rising edges plus the setup & hold times. For those applications where the control processor has no knowledge of the Sclk period, this will imply a CEN period of 5 Sclk rising edges. 2. Production test will use rise and fall time less than 7ns. Specified rise and fall times are guaranteed by design. 3. Sclk is required for proper bus timing. Sclk must always be faster than twice the fastest 1X data clock. 4. The meaning of DACKN is that data will be valid before the end of the C4 time. 5. All voltage measurements are relative to gnd. Input and output levels are those shown in "DC Electrical Specifications". For testing, inputs switch between 0.2 and 2.8V; outputs are measured between 0.8 and 2.0V. 6. Some values not tested, but guaranteed by design.
1995 May 1 DAKdly T/RFx1 Tgpirtx TC/TO FC/T Fx1 FIGURE GPO valid after write to GPOR I/OP falling edge to TxD out 1X mode RxD setup to I/OP rising edge 1X mode GPI to Rx/Tx clock out DACK high from CEN high (ASYNC) DACK low from Sclk C4 rising edge Delay C/T clock external to output pin C/T high and low time Clock frequency X1 Rise / Fall time X1 Low / High time X1 clock frequency PARAMETER
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
DACK high from C4 end rising edge (SYNC)
378 MIN 35 25 25 0 0
SC26C198 SC68C198 SC26L198 SC68L198
LIMITS
3.6864
TYP
100 32 23
10 / 10
MAX
100 125 8.0 80 45 45 42 8
Product specification
UNIT
MHz
MHz
ns ns ns ns ns ns ns ns ns ns ns
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
C1
C2
C3
tCH C4
SCLK tRWD CEN
W_RN tRWH
ADDRESS
INVALID
VALID
INVALID
DATA
INVALID
VALID
INVALID
DACKN tCS tRWS tAS tAH tDS DAKDLY C4 tDH DAKDLY CEN HIGH
SD00194
Figure 2. Basic Write Cycle, ASYNC
C1
tCS
C2
C3
C4
SCLK tCH CEN tSTP
W_RN tRWH
ADDRESS
INVALID
VALID
INVALID
DATA
INVALID
VALID
INVALID
DACKN tAS tRWS tAH tDS
DAKDLY C4 tDH
DAKDLY C4 END
SD00195
Figure 3. Basic Write Cycle, SYNC 1995 May 1 379
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
C1
C2
C3
tCH C4
SCLK tRWD CEN
W_RN
tRWH
ADDRESS
INVALID
VALID
INVALID
DATA
INVALID
DATA=00
VALID
INVALID
DACKN tCS tRWS tAS tAH tDD DAKDLY C4 tDF
DAKDLY CEN
SD00196
Figure 4. Basic Read Cycle, ASYNC
C1
tCS
C2
C3
C4
SCLK tCH CEN tSTP
W_RN
tRWH
ADDRESS
INVALID
VALID
INVALID
DATA
INVALID
DATA=00
VALID
INVALID
DACKN tRWS tAS tAH tDD DAKDLY C4 DAKDLY C4 END tDF
SD00197
Figure 5. Basic Read Cycle, SYNC 1995 May 1 380
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
C1 SCLK
C2
C3
C4
IACKN
CEN
W_RN
DON'T CARE
ADDRESS
INVALID
DON'T CARE
INVALID
DATA DACKN tCS
INVALID
VALID
INVALID
tAS tRWS
tAH tDF tDD C4 DAKDLY DAKDLY CEN HIGH
NOTE: CEN must not be active during an IACKN cycle. If CEN is active, IACKN will be ignored and a normal read or write will be executed according to W_RN. In the synchronous mode, extended IACKN signal will start another IACKN. (This may not be desired, but is allowed.)
SD00525
Figure 6. Basic IACKN Cycle, ASYNC/SYNC
+5V T/R fX1 X1 L/H
1K required for TTL gate. X1
fX1
NC
X2
C1 = C2 = 24pF FOR CL = 20PF C1 and C2 should be chosen according to the crystal manufacturer's specification. C1 and C2 values will include any parasitic capacitance of the wiring. C1
26C94
X1 BRG 3pF 50 KOHMs TO 150 KOHMs X2 3.6864MHz 4pF MUX /2 To remainder of circuit 22 STANDARD BAUD RATES
C2
38.4kHz CLOCK TO I/O CHANGE-OF-STATE DETECTORS
NOTES: C1 and C2 should be based on manufacturer's specification. X1 and X2 parasitic capacitance IS 1-2pF AND 3-5pF, respectively. GAIN: at 4MHz 8 to 14db; at 8MHz 2 to 6db PHASE: at 4MHz 272 to 276; at 8MHz 272 to 276 The above figures for 5V operation. Operation at 3V is to be determined.
TYPICAL CRYSTAL SPECIFICATION FREQUENCY: 2 - 4MHZ 12 - 32pF LOAD CAPACITANCE (CL): TYPE OF OPERATION: PARALLEL RESONANT, FUNDAMENTAL MODE
SD00198
Figure 7. X1/X2 Communication Crystal Clock 1995 May 1 381
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
T/RFSCLK tSCLKL tSCLKH fSCLK
SD00199
Figure 8. SCLK Timing
T/RFSCLK TC/TL TC/TH
FC/T TC/TO
SD00200
Figure 9. Counter/Timer Baud Rate Clock, External
T/RF Trx Ttx TC/TH Frx Ftx TC/TO
SD00201
Figure 10. Tx/Rx Clock Timing, External
1X DATA CLOCK tRXH RxD tTXD TxD tRXS
SD00202
Figure 11. Transmitter and Receiver Timing Note: CEN must not be active during an IACKN cycle. If CEN is active IACKN will be ignored and a normal read or write will be executed according to W_RN. In the synchronous mode extended IACKN signal cycle will start another IACKN. (This may not be desired but is allowed)
1995 May 1
382
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
INDEX
GRxFIFO, 360 GTxFIFO, 360
Numbers
1x and 16x modes, Receiver, 342 1x and 16x modes, Transmitter, 342
H
Host Interface, 339 Host interface, 339
A
Address Recognition Character Register, 357 ARCR, 357 Asynchronous bus cycle, 339
I
I/O Port Configuration Register, 360 I/O Port Interrupt and Output Register, 360 I/O ports, 343 I/OPCR, 343, 360 I/OPIOR, 360 IACKN, 341 IACKNCycle, 345 ICR, 358 IMR, 341, 356 INDEX, 381 Input Port Register, 360 Interrupt Arbitration, 344 Interrupt Control, 341 Interrupt Mask Register, 356 Interrupt sources, Enabling, 345 Interrupt Status Register, 356 Interrupt Vector Register, 359 Interrupts, Xon/Xoff, 349 IOPIOR register, 344 IPR , 360 ISR, 341, 356 IVR, 359
B
Baud Rate Generator , 340 BCRA, 357 BCRBRK, 357 BCRCOS, 357 BCRx, 357 Bidding Control Register - Address, 357 Bidding Control Register - Break Change, 357 Bidding Control Register - Change of State, 357 Bidding Control Register - Xon, 357 Block diagram, 339 Break, transmission of, 342 BRG Timer Control Register, 358 BRG Timer Reload Registers, Lower, 358 BRG Timer Reload Registers, Upper, 358 BRGCTCR , 358 BRGTRL, 358 BRGTRU, 358
C
CEN, 339 Channel Blocks, 340 Channel Status Register, 355 Character Recognition, 340 CharacterStripping, 344 CIR, 359 Clock Register, Rx & Tx, 352 Command Register, 353 COMMAND REGISTER TABLE, 355 CR , 353 Crystal oscillator, 340 Current Interrupt Register, 359
M
Minor Modes, 347 Mode control, Xon/Xoff, 349 Mode Register 1, 351 Mode Register 2, 351 Mode Registers, Initialization, 350 Modes of Operation, 346 MR0 , 350 MR1, 351 MR2, 351 Multidrop mode, 344
O
Overrun error, 343
D
Description, 335 DESCRIPTION, over all, 339
P
Parity error, 343 Pin Description, 338 Pinout, 337 Polling, 345
F
Framing error, 343
G
GCCR, 350 General Purpose Pins, 344 GIBCR, 359 GICR, 359 GITR, 360 Global Configuration Control Register (GCCR), 350 Global Interrupting Byte Count Register, 359 Global Interrupting Channel Register, 359 Global Registers, 341, 344 Global RxFIFO Register, 360 Global TxFIFO Register, 360 GPOC , 361 GPOD, 361 GPOR, 361 GPOSR, 361 1995 May 1 383
R
Receiver, 342 Receiver FIFO, 343, 357 Receiver Status Bits, 342 REGISTER DESCRIPTIONS, 350 Register Map, 362 Register Map, Control, 362, 363 Register Map, Data, 363, 368 Reset Conditons, 371 RxCSR , 352 RxFIFO, 357
S
Sclk, 339 SR , 355 Synchronous bus cycle, 339 System Clock, 340
Philips Semiconductors
Product specification
Octal UART with TTL compatibility at 3.3V and 5V supply voltages
SC26C198 SC68C198 SC26L198 SC68L198
T
Timing Circuits, 340 Transmitter, 341 Transmitter FIFO, 342, 357 Tx, Status Bits , 341 TxCSR , 352 TxEMT, 341 TxFIFO, 357 TxRDY, 341
Wake up mode, 344 Wake Up modes, 347 Wake up. Default, 347 Watch-dog Timer , 347 Watch-dog Timer Enable Register, 358 WDTRCR, 358
X
XISR, 358 Xoff Character Register, 357 XoffCR, 357 Xon /Xoff characters , 348 Xon Character Register, 357 Xon-Xoff Interrupt Status Register, 358 Xon/Xoff modes, 348 Xon/Xoff Operation, 348 XonCR , 357
U
UCIR, 359 Update CIR, 345, 359
W
Wake Up Mode, 347
1995 May 1
384

▲Up To Search▲

Price & Availability of SC26C198

	To Download SC26C198 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .